Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Flattening a glue up with a drum sander

Featured Replies

I have a supermax 19-38 that I have very little experience with and I'm looking for some advice on how to use it. 

I just glued up two halves of a maple countertop. Each slab is 14.5" wide x 72" long x 1-7/8" thick. Each slab is made up of 9 boards with edge grain up. Each board was aligned with dominos but the slabs have a slight bow. I need to flatten them before glueing them together.

My first instinct is to follow Marc's instructions on flattening a wide slab in the roubo build video; flatten one side with a jack plane then send it through the planer to flatten the opposite side.

Can or should I use my drum sander to flatten these slabs instead? 

Do I still have to hit one side with the jack plane before sending it through the drum sander?

Thanks.

Just like a planer, your drum sander will only get the top as flat as the reference side. Assuming you have a planer that will do 14.5"w, I would be using that because it will take many many more passes with the drum.  

Get one side flat,  I prefer to take the offending high ends off rather than the whole belly bow, set up your in and outfeed and plane the other side to consistent thickness. If your first side is straight with no twist, your top should be also. 

Depending on how bad the bow is and considering the size of those things...I might just build a router sled and flatten with that instead.  That could be a lot of grunt work to flatten with a hand plane, especially if it's hard maple.

Or you can make a giant sled for your drum sander, but Brendon's right...it's a lot of work to keep passing those beasts through over and over again.

You would need to build a big sled and put the top in place with double faced tape. Add shims under any gaps. I use playing cards for small gaps then tape them down. Use fairly coarse abrasive and don't try to take more than a 1/4 turn on each pass. I set up infeed and outfeed support rollers and put a table beside the machine to help transfer the top & sled back to run it again.

its either that or some excersize with a plane.

  • Popular Post

This just came up in a recent thread of mine. Feel free to search for it if you want more detail, but I made an enormous end grain island that bowed slightly during my glue up. I was using two bessey parallel clamps joined together with their extenders and the clamps flexed under pressure. Regardless of how I got there, this is how I fixed it. I think my bow was like 1/8" in the middle over a length of 65-70". It wasn't terrible, but I wasn't happy with it either. I don't know how much of a bow your piece has, but I would put the frown side up on my bench, joint a 72" long board(8/4 would be nice for stability), lay that on your countertop to use as a straight edge, and then begin taping shims to the piece. In my photo, you can see I have a bajillion business cards taped to the piece in a grid. My middle had about 5 business cards and it tapered off from there to 4, 3, 2, 1. Repeat this across the width of your piece. This should give you a "sled" of sorts for your drum sander--A sledless sled. Your shims will make your one side reference flat on your planer or drum sander bed. This will result in a corresponding flat opposite face. After you clean up your one face, remove all the shims and reference off your flat and straight face. Believe it or not, my business card method resulted in damn near perfection. I forget what it ended up as, but we were talking feeler gauges over that long length, which is plenty good enough for an island top of that size.

IMG_2051.JPG

IMG_2062.JPG

  • Author

Thanks for the replies guys. 

I have a 15" planer, but never tried to run anything this wide through it. My original plan was to hit it with the jack and run it thru the planer. I began to doubt the plan when I started thinking if I don't feed it perfectly straight then it may get hung up.

Pwk5017, I did find your thread in a search. Thanks for elaborating and adding pics. I think I am leaning toward your solution. I haven't really used my drum sander yet so I'm a little nervous to practice on this piece. I guess I have enough material to remove, so hopefully that will leave enough room for error.

Thank you. 

Matt 

Have fun remember that a drum sander is not a planer,  you can't just crank down and it will thickness to that depth.  The drum requires more patience, light passes, and is quite a bit slower.

I would not put a table top that is made from "end grain" through a planer. In my opinion the drum sander is the way to go on end grain table top................

2 minutes ago, Gary-ks said:

I would not put a table top that is made from "end grain" through a planer. In my opinion the drum sander is the way to go on end grain table top................

Each slab is made up of 9 boards with edge grain up. 

Yeah, mine was end grain, the OP has it much easier with edge grain. The only thing with planer versus drum sander is the feed mechanism. I would be wary with affixing  the cards for feeding through the planer. See, with the drum sander, the cards stay put and the bed moves along with the card. I would be nervous with the planer, because your cards/shims might come loose. 

 

First thing is first, joint your board and lay it across the piece. You need to quantify the problem at hand. 

  • Author
7 hours ago, Pwk5017 said:

I would be wary with affixing  the cards for feeding through the planer. See, with the drum sander, the cards stay put and the bed moves along with the card. I would be nervous with the planer, because your cards/shims might come loose. 

Exactly. I don't think the cards and the planer bed rollers would play nice together. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.