Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Old planer ripipng the wood up, Super 125

Featured Replies

Just bought an old super 125 penn state industries surface planer.  I had all the blades sharpened and then reinstalled them.  When I run the boards through it is ripping small holes into the pine boards.  Its also creating snipe but I know why that is.  Anybody recognize this problem.  When I bought the machine I had the seller run a board through and it looked fine.  Also,  I wasn't sure of the blade height so I screwed the leveling screws all the way down and then firmly pressed the blade down making sure it was level on both sides.

I tried to google blade height for this machine but could not find any info, I am hoping some one here can help  me out

 

Thanks

Ryan

0607160910.jpg

  • Author

I try to take off an extremely small amount but the rollers do not catch the wood to pull it forward.  So I have to keep bringing it down until the board catches the rollers.

Sounds like mabe the blades  you installed are not adjusted right..Mabe to far out but Im no expert.

 Generally the term surface planer refers to jointer but I take it we're talking about   Thickness planers  . From what I can see  your pressure bars and rollers are Not set  to the cutting Circle that the knives create . These are generally set it within 1/32" of each other.  Modern machines  avoid this complication by providing knife setting Jigs  to maintain proper cutting circle diameter and knife projection on the cutter  block .   Your manual should either give you the settings of all of these but there are some generic measurements and ways of going around it .  In general feed rollers and pressure bars or set below the cutting Circle . 

 

 Lastly is that wood dry?if it's green it will not plain like dry pine  and generally exhibits that type of surface as well . I suspect your adjustments are off by your comment about not being able to do a light cut 

It's not clearing the chips before it goes under the feed rollers or pressure bar.  You probably need to move a lot more air, or something is missing, or misplaced under there.  I knew a cabinet maker decades ago that had an old Whitney planer that did that until they did something to blow the chips out of the way.

As best I can tell from the pic it seems to be tearout, not dimpling from spoil being pressed into the surface, yes?  If the knives are well sharpened and it is tearout I am in the "knife or knife relationship to the feed rollers" camp.  A poor man's Rotocator can help with checking the delta between knives and rollers.

Rotocator-poor-mans.jpg

This is just a 1-2-3 block with a bolt and knob holding a dial indicator in place.

just to further illustrate what Gee is checking in relationship to the cutting circle. I am assuming all the knifes in the cutter block are set to within .002" or better for a true 3 knife cut. The way you describe your setting method should be reviewed with the dial that Gee shows because setting  the hight from  the bottom of the jack screw is at best within .020".  read off the table for the knife's is best because it eliminates any head to planer bed  misalignment. In terms of setting up a planer we really are splitting hairs here and it is important to the quality of the finish.

 

 wadkinfm_zps1ce25838.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.