Recommended Posts

Posted
8 hours ago, shaneymack said:

Ya it's standard here. Our development (about 150 custom homes so far) is pretty much all like this. Never had an issue

There is also the expanding style of connection. Uponor is one brand. You ever use / come across it?

Supposed to be less restriction through the system than the crimp ring due to the fittings being larger diameter.

I think for the OP, as long as your local jurisdiction allows the use of shrakbite style in a closed wall go for it. It would be a bit spendy for a whole job though. Might just be worth having a plumber come in and sweat the joints for you.

Posted
There is also the expanding style of connection. Uponor is one brand. You ever use / come across it?

Supposed to be less restriction through the system than the crimp ring due to the fittings being larger diameter.

Not familiar with it, Alan. Most things that come out in the US take years before we see it here.

It seems to be an upgraded pex pipe?

http://www.uponor.ca/residential-plumbing/homeowner/pex-explained.aspx#sidebar-navigation

Sent from my SM-N910W8 using Tapatalk

Posted
9 hours ago, shaneymack said:

Ya it's standard here. Our development (about 150 custom homes so far) is pretty much all like this. Never had an issue

Sent from my SM-N910W8 using Tapatalk

Ya we have sharkbite up here but no respectable plumber would ever plumb a new build with that. Mostly used by guys in renovations.

Sent from my SM-N910W8 using Tapatalk

I took a plumbing course from the local college a few years back.  The master plumber teaching the course talked about sharkbite fittings.  He said they can only be used in areas that are accessible and cannot be permanently covered according to code.  He recommended them for temporarily repairing a line until it could be repaired properly.  He said he did find the sharkbite cap handy for pressure testing a line though, so he wouldn't have to keep soldering a cap on and then cutting it off.

  • Like 1
Posted

I took a plumbing course from the local college a few years back.  The master plumber teaching the course talked about sharkbite fittings.  He said they can only be used in areas that are accessible and cannot be permanently covered according to code.

I'm not sure if this is true. I know Home depot (in Ottawa) has a shower mock up in the plumbing section with all sharkbite fittings. They are selling it to people as an easy way to plumb for beginners. I'm not saying Home depot is the authority on plumbing but I don't think they would be encouraging people to plumb against code. I'll give my plumber a call tomorrow and ask him. Im curious now.

Sent from my SM-N910W8 using Tapatalk

  • Like 1
Posted
19 minutes ago, shaneymack said:

 

 

 

 

I'm not sure if this is true. I know Home depot (in Ottawa) has a shower mock up in the plumbing section with all sharkbite fittings. They are selling it to people as an easy way to plumb for beginners. I'm not saying Home depot is the authority on plumbing but I don't think they would be encouraging people to plumb against code. I'll give my plumber a call tomorrow and ask him. Im curious now.

 

 

Sent from my SM-N910W8 using Tapatalk

 

21 minutes ago, shaneymack said:

 

 

 

 

I'm not sure if this is true. I know Home depot (in Ottawa) has a shower mock up in the plumbing section with all sharkbite fittings. They are selling it to people as an easy way to plumb for beginners. I'm not saying Home depot is the authority on plumbing but I don't think they would be encouraging people to plumb against code. I'll give my plumber a call tomorrow and ask him. Im curious now.

 

 

Sent from my SM-N910W8 using Tapatalk

I have seen this as well in the local HD, showing a method for DIY people to get plumbing done.  Maybe I am misremembering - I'll dig out my old class notes to confirm.

From their website 

Q: What standards and codes do SharkBite fittings comply?

A:  SharkBite fittings are certified to ASSE 1061, NSF/ANSI 61, NSF/ANSI 14 and NSF/ANSI 372. They are listed by IAPMO and CSA. SharkBite fittings are compliant with the Uniform Plumbing Code (UPC), National Plumbing Code of Canada and the International Plumbing Code (IPC). Since local code varies by area, please consult with local plumbing codes for specific applications.

  • Like 1
Posted

Sharkbite work because water pressure pushes the pipe into the o-ring. With PEX there is flex. There is enough flex that freezing does not burst the line. (It can burst fittings.) PEX has memory. Kink a line for fun once and then take a heat gun to it. You can heat the line and the kink will heal. Most codes won't let you use it once kinked, but it can be done. 

Posted

Oh I looked up the code: municipality follows the county, county follows the state, state code is online.  It is fine.  Since this is a small job, I was interested in the sharkbite fittings because it'll be cheaper than getting a crimp tool even though the fittings are more.  If I was doing a lot of work then I'd buy the crimping tools. 

Posted
2 hours ago, Gilgaron said:

Oh I looked up the code: municipality follows the county, county follows the state, state code is online.  It is fine.  Since this is a small job, I was interested in the sharkbite fittings because it'll be cheaper than getting a crimp tool even though the fittings are more.  If I was doing a lot of work then I'd buy the crimping tools. 

The local builder supply rents. (Full cost deposit that is fully refunded if you buy rings and fittings from them.) Worth a phone call. Buy a Go/No Go gauge. The tool must be as perfectly perpendicular to the line/ring as you can get it. 

  • Like 1
Posted
3 hours ago, Gilgaron said:

Oh I looked up the code: municipality follows the county, county follows the state, state code is online.  It is fine.  Since this is a small job, I was interested in the sharkbite fittings because it'll be cheaper than getting a crimp tool even though the fittings are more.  If I was doing a lot of work then I'd buy the crimping tools. 

The local store here will lend out a crimper tool if you buy that parts from them.  Might be worth an ask if you have a local hardware store.

Posted

I looked it up and they do have tool rentals... hmm... the one spot will still be very annoying to sweat but I could just do the push-to-fit there with an access panel and bury the sweated and crimped ones comparatively worry free... thanks for all the feedback and discussion guys!

Posted
6 hours ago, Gilgaron said:

I looked it up and they do have tool rentals... hmm... the one spot will still be very annoying to sweat but I could just do the push-to-fit there with an access panel and bury the sweated and crimped ones comparatively worry free... thanks for all the feedback and discussion guys!

Be careful, you shouldn't sweat a connection near the Sharkbite (risk of melting the plastic) so it will need to be the last connection you make.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 46 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32k
    Total Topics
    437.5k
    Total Posts
  • Member Statistics

    26,007
    Total Members
    3,644
    Most Online
    FurniCore
    Newest Member
    FurniCore
    Joined