Gilgaron Posted October 10, 2016 Report Posted October 10, 2016 I know lots of woodworkers are DIYers so I thought I'd ask if any of you have tried PEX and sharkbite connectors: My Dad and I tried to reroute some copper water supply lines up into the ceiling joists in the basement to allow the ceiling to be finished without a soffit there and attempt 1 was not a success. We ran out of time so we tore off our leaky mess. After all that 'practice' my job sweating on some caps to allow us to turn the water back on for the rest of the house went well, so everything is temporarily ok, except for the bathroom nominally fed by those pipes. For attempt 2 I've read some tips on doing a better job sweating the joints without melting the ones we already did, but I've also been increasingly tempted to just buy some of those sharkbite push-to-connects and some pex and be done with it. I've not worked with it before but it sounds like it is pretty easy. Any opinions one way or the other? The connectors cost more than copper fittings, but if it is just as good, that's a lot of time I can spend not pretending to be a plumber. Quote
Woodenskye Posted October 10, 2016 Report Posted October 10, 2016 I like the shark bite connectors and they work really well. Just make sure you get the remover tool, it's a little plastic thing but does the job. They may cost more, but still cheaper than a plumber. Quote
Dknapp34 Posted October 10, 2016 Report Posted October 10, 2016 I won't pretend to have any experience with plumbing, but I recall the guys on the Fine Homebuilding podcast saying good things about those connectors. Quote
Tpt life Posted October 10, 2016 Report Posted October 10, 2016 Sweat is easy, but pex and shark bite are fast. No failures yet after four years (the oldest emergency repair in my house.) I would not shark bite a new install, but for an exposed problem area they work well. 1 Quote
Elroy Skimms Posted October 10, 2016 Report Posted October 10, 2016 I've added several bathrooms and kitchens onto existing lines with PEX and SharkBite. Never once had a leak. Woodenskye is right though, get the removal tool. Actually, get several. Nothing like dropping it on the ground and having to fumble around in a spider-filled crawlspace, praying that the thing you just grabbed is an old discarded snakeskin boot and not a live snake. Always have spares! -E Quote
Beechwood Chip Posted October 10, 2016 Report Posted October 10, 2016 I've used them for emergency repairs in difficult locations. They seem to work well. At work our facilities guys insist on sweated/glued connections. We had a restaurant in our building blow a press-on connection and drain the HVAC for the whole building. Our facilities guys were all, "See! That's why we only do sweated connections." Quote
hawkeyestoob Posted October 10, 2016 Report Posted October 10, 2016 One of the tricks to getting a good sweated connection that I have learned over the years is to get everything at the joint as dry as possible before you start. The moisture there can cause all sorts of problems for you. The guys that do it all the time seem to be better at dealing with it and I have found that if I start with everything dry and can keep it that way while I am sweating the joint my success rate goes WAY up. Quote
Chestnut Posted October 10, 2016 Report Posted October 10, 2016 I don't know if it was sharkbite fittings but i had one of those push on pex fittings no hold. I was helping a friend and he insisted on not letting me sweat the fittings. It was in a very hard to reach location so i put it down as user error. I think sweating is easier then the pex fittings but I've done a fair bit of it. Good flux and not over heating things is key in my opinion. Quote
Tpt life Posted October 10, 2016 Report Posted October 10, 2016 PEX needs collets and ferrules (terms are escaping me.) Most PEX failures I have repaired were because someone omitted the shaping sleeve that goes inside the pipe to give it rigidity under compression. It deform and not seal well when those bits are omitted. Quote
socoj2 Posted October 11, 2016 Report Posted October 11, 2016 15 hours ago, C Shaffer said: PEX needs collets and ferrules (terms are escaping me.) Most PEX failures I have repaired were because someone omitted the shaping sleeve that goes inside the pipe to give it rigidity under compression. It deform and not seal well when those bits are omitted. If you use metal fittings elbows etc, you dont need it. Quote
shaneymack Posted October 11, 2016 Report Posted October 11, 2016 Most PEX failures I have repaired were because someone omitted the shaping sleeve that goes inside the pipe to give it rigidity under compression. It deform and not seal well when those bits are omitted. What sleeves are you referring to? The fittings slide into the pipe and that is what gives rigidity and a place to compress the ring. You guys use a different system down there or I'm just misunderstanding? Sent from my SM-N910W8 using Tapatalk Quote
socoj2 Posted October 11, 2016 Report Posted October 11, 2016 30 minutes ago, socoj2 said: If you use metal fittings elbows etc, you dont need it. actually now that i think about it. I dont know that you need any internal sleve with plastic fittings either. Quote
Gilgaron Posted October 11, 2016 Author Report Posted October 11, 2016 The sleeve he's talking about is for the sharkbite/gatorbite push-to-fit fittings, which don't use the rings. http://www.homedepot.com/p/SharkBite-1-2-in-Brass-Push-to-Connect-Coupling-U008LFA/202270492 The importance of drying the pipes was impressed upon me when we took the leaky stuff back off... heating the solder with the moisture in there (and still dripping through) made everything let go surprisingly easily. From some other reading I did I think the biggest mistake I made was in fluxing all the joints, putting it together, and then soldering them one by one... I likely melted out the flux of the subsequence joints before I got to them. 1 Quote
Elroy Skimms Posted October 11, 2016 Report Posted October 11, 2016 1 hour ago, shaneymack said: The fittings slide into the pipe and that is what gives rigidity and a place to compress the ring. I'm pretty sure those fittings are not designed for PEX. I use those barbed fittings for tube/hose connections with water pumps and such, but not for plumbing a house. -E Quote
shaneymack Posted October 11, 2016 Report Posted October 11, 2016 I'm pretty sure those fittings are not designed for PEX. I use those barbed fittings for tube/hose connections with water pumps and such, but not for plumbing a house. -E Yes, they are all standard pex fittings. Sent from my SGH-I337M using Tapatalk Quote
Tpt life Posted October 11, 2016 Report Posted October 11, 2016 1 hour ago, shaneymack said: What sleeves are you referring to? The fittings slide into the pipe and that is what gives rigidity and a place to compress the ring. You guys use a different system down there or I'm just misunderstanding? Sent from my SM-N910W8 using Tapatalk Yes, four or five different systems in fact. Sharkbite and Maniblock are two different, comparable, all "plastic" systems that require no crimping of rings. Quote
Elroy Skimms Posted October 11, 2016 Report Posted October 11, 2016 Just now, shaneymack said: Yes, they are all standard pex fittings. Sent from my SGH-I337M using Tapatalk Yikes, I would never even think to try those for plumbing a house. I've had a few of those pop loose under low pressure from a fountain pump. -E Quote
Tpt life Posted October 11, 2016 Report Posted October 11, 2016 2 minutes ago, Elroy Skimms said: Yikes, I would never even think to try those for plumbing a house. I've had a few of those pop loose under low pressure from a fountain pump. -E PEX with the crimp rings will not bust loose when installed properly. Quote
Elroy Skimms Posted October 11, 2016 Report Posted October 11, 2016 Just now, C Shaffer said: PEX with the crimp rings will not bust loose when installed properly. Ah, crimp rings. Yes, that would make a big difference. Now that I think about it, I think that's what my current house has. I didn't build this one, but I think that's what was used by the builder. -E Quote
shaneymack Posted October 11, 2016 Report Posted October 11, 2016 Ah, crimp rings. Yes, that would make a big difference. Now that I think about it, I think that's what my current house has. I didn't build this one, but I think that's what was used by the builder. -E Ya it's standard here. Our development (about 150 custom homes so far) is pretty much all like this. Never had an issue Sent from my SM-N910W8 using Tapatalk Yes, four or five different systems in fact. Sharkbite and Maniblock are two different, comparable, all "plastic" systems that require no crimping of rings. Ya we have sharkbite up here but no respectable plumber would ever plumb a new build with that. Mostly used by guys in renovations. Sent from my SM-N910W8 using Tapatalk 1 Quote
Tpt life Posted October 11, 2016 Report Posted October 11, 2016 11 minutes ago, shaneymack said: Ya it's standard here. Our development (about 150 custom homes so far) is pretty much all like this. Never had an issue I am seeing more of the heated double ring rather than steel crimp now. Quote
Beechwood Chip Posted October 11, 2016 Report Posted October 11, 2016 I've heard that an advantage of copper pipes is that they will self-heal around pinhole leaks. The copper corrodes when exposed to air and water and the corrosion seals the leak. Not sure if that's true, and besides, the extra expense of copper probably isn't worth it. Quote
Rapid Roger Posted October 11, 2016 Report Posted October 11, 2016 I have a fairly old house built in 1954 and of course it had the old galvanized steel plumbing. When some new plumbing needed to be done sometime in the 70's, copper was used and one piece failed in the 90's with a pinhole about midway of a 6'-0" section. All of the older steel was holding up well but, I got worried about it and had the whole house (water and sewer) replaced. The plumber used plastic lines EVERY PLACE. Very few connections, no rot or rust or corrosion anywhere and a manifold that allows me to shutoff any one water line (hot or cold) when necessary (for faucet replacement for example) and not effect any other place in the house. I think it is the greatest thing to happen since running water was invented! (Well other than water softeners and tank-less hot water heaters also) Just my 2 cents worth. Quote
Tpt life Posted October 11, 2016 Report Posted October 11, 2016 I will typically go PEX. Fewer connections that are deeply buried is one big plus. The other is the virtual elimination of galvanic corrosion that is common with mixed metals in a system. Quote
BonPacific Posted October 11, 2016 Report Posted October 11, 2016 Never worked with PEX, but I've used sweated and sharkbite connections for home repairs/updates (no nearby shutoffs for sink and outdoor faucets). Both have their place, though I trust the physics of sweated connections more than sharkbite. I used a sharkbite valve because that was what was available locally. The Sharkbite connections are only a year old, but shows no sign of stress or weakening. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.