mike030941 Posted December 9, 2016 Report Posted December 9, 2016 I recently purchased the Jet 8" helical head jointer. I've got it all set up but upon start up, I'm noticing some vibration. I checked the pulleys and associated keys on both the motor and cutter head and both seem to be set properly. It doesn't necessarily happen every time, but more often than not it does. Has anyone else had an issue similar to this? If so, what did you do to fix the issue? If more details are needed, I can supply. Thanks! Quote
drzaius Posted December 9, 2016 Report Posted December 9, 2016 When I got my General Int. jointer it vibrated more than I liked so I put a link belt on it & it calmed right down. I'm sure a good quality V belt would have done the same. 1 Quote
minorhero Posted December 9, 2016 Report Posted December 9, 2016 I prefer cogged belts to link belts. achieved the same results but cheaper. The fact it doesn't vibrate consistently is odd. How much vibration are we talking about ? Enough to cause a ripple in a glass of water placed on the bed, or enough to walk the machine across the room? Any sounds that occur only when vibrating ? does vibration occur only during startup and shutdown or only after heavy use or all the time till shut down ? 1 Quote
estesbubba Posted December 9, 2016 Report Posted December 9, 2016 If it only happens on startup I wouldn't worry too much about it. If it continues once the motor has spun up then I would track it down. 1 Quote
mike030941 Posted December 9, 2016 Author Report Posted December 9, 2016 Yes, it's only upon startup with only slight continuous vibration after (not sure I'd even call it vibration). It's not enough to shake the machine. With it being inconsistent, I feel like it's a belt issue, where maybe it swelled in a specific area causing it. It almost sounds as if its a chattering with the belt, but everything seems aligned and tensioned properly. thank you all for feedback. Quote
drzaius Posted December 10, 2016 Report Posted December 10, 2016 3 hours ago, minorhero said: I prefer cogged belts to link belts. achieved the same results but cheaper. Agreed, but I had bought one for my old jointer that required major disassembly to replace the belt. So I used it on the new one. Quote
minorhero Posted December 10, 2016 Report Posted December 10, 2016 15 hours ago, mike030941 said: Yes, it's only upon startup with only slight continuous vibration after (not sure I'd even call it vibration). It's not enough to shake the machine. With it being inconsistent, I feel like it's a belt issue, where maybe it swelled in a specific area causing it. It almost sounds as if its a chattering with the belt, but everything seems aligned and tensioned properly. thank you all for feedback. It's the belt. Regular belts develop a "memory"where they bulge slightly representing where they spend most of the time touching the pulleys. When starting up (especially after not being used for 1+ days) that bulge will contact the belt guard at speed causing the vibration. a link belt or cogged belt will alleviate or solve this problem . But the vibration should not be severe enough to really cause any kind of problem . Quote
davestanton Posted December 14, 2016 Report Posted December 14, 2016 Yes to the belt. Buy a quality belt from an automotive spares store. The belts from Asia have a sideways bump near the join and only noticeable at startup and when coasting to stop. Mine does it but doesn't bother me enough to change it....yet. lol. Quote
mike030941 Posted December 15, 2016 Author Report Posted December 15, 2016 Thanks everyone for the input. It seems like it is just the belt. I will likely replace, but similar to Dave, now that I have been using it I am somewhat getting used to it. It just seems odd to me that a piece of machinery like this would scrimp on belts - would be nice to see them come with cogged or linked belts, but I guess that is just wishful thinking. Thanks again everyone. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.