Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Hi from Woodland, WA!

Featured Replies

Hi There,

post-3363-0-85282900-1294596635_thumb.jppost-3363-0-49827400-1294596704_thumb.jppost-3363-0-96810600-1294596731_thumb.jppost-3363-0-69602100-1294596983_thumb.jppost-3363-0-53738000-1294597024_thumb.jppost-3363-0-80621200-1294597047_thumb.jp

My name is Jodi.

I make cowhide mirror frames.

They are currently made out of 2x6 KD lumber from a Home Improvement store such as Home Depot or Lowes.

A few of the first ones I made twisted/warped a bit so they wouldnt sit flush against the wall.

So I started kerfing the bottom of the 2x6's (2 rows about 1/8" inch deep) I noticed that one of the mirrors still warped.

Then I bought 2x6 DECKING boards, the pros to that were....the frames ended up weighing alot less (because the decking boards are alot lighter), and they were already kerfed. the cons....the decking boards were rounded on the underside which made cuting my cowhide difficult and looked sloppy and the decking boards were super expensive!

The frames are currently put together by 45ing the corners, using lumber connecters (the kind with the spikes the you hammer down into the wood) on the backside of the frames and then sinking a screwinto the corner to suck to two pieces of wood together. I'm trying to come up with the most cost effective way to makes these frames so they are as light as possible, sturdy, and do not warp. Do you think biscuit joining them would make a difference? Please keep in mind that they are totally covered with either cowhide on the front or paper on the back so the are for structure only. Also, that embellishments are usually screwed into the corners of the frame from the front so keep that in mind when suggesting assembling techniques. Also, that I want the thickness and with width of a 2x6. Any suggestions would be greatly appreciated. thank you

Hello, KC. And welcome to the site. I Had a similar problem with a very large frame. I made the facing piece to the width needed. Then added a piece to the outer edge to get the thickness required. For the inner piece I did the same with it being inset to recieve the painting. I ended up with an "F" shaped cross section frame. The top of the "F" was the outside edge. The facing 3/4" thick, as was the outer edge piece. The inner piece was 1/2", and set in far enough to allow a 1/2" covering of the edge of the painting. My wife (Management) liked it a lot, so I guess it is ok. Anyway, good luck.

i think biscuts would work fine if you own the jointer already, if not you can glue the mitered corners together once the glue has cured make a sline joint with a jig and your table saw

as in this video. hope this helps dave

Wow, those are beautiful frames.

I think that as long as you're using construction lumber, warping and twisting will be a fact of life unless you go to the trouble of letting it dry out and then planing it flat again after it has warped all it's going to. For what you're doing, that's probably more trouble than it's worth.

It seems like the answer might be to use some different material. Before making any stupid suggestions, though, I have one question. What holds all those little metal dots in place? Are those the heads of nails of some sort? Do they have to be driven into solid wood?

Also, I'm wondering why the dots indicated by the red arrow are higher than all the others? Everything else seems so perfect that I can't believe that's a mistake.

-- Russ

post-685-0-26352400-1294716280_thumb.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.