lewisc Posted September 21, 2017 Report Posted September 21, 2017 This will be a short journal, some more sanding and finessing to do and it will be done. I've been going cutting board crazy recently. A friend from work asked if I could make one that would fit in her kitchen bench top. The bench top used to have a stovetop built in and rather than replace the bench, a cutting board could work. The board won't be resting on the edges, rather, it will be supported from underneath and siliconed to the bench. I'm not sure if this will present any problems. This is by far the biggest one I've made and I was hesitant to take it on but I accepted the challenge. After today's effort, I'm actually thinking it might work. The biggest challenge is that she's moving 2000km (1250miles) away. Going off the measurements given, I'm hoping it fits. There may have been better ways to go about it but this is what I've come up with. - I started by preparing the board - I had a problem with the strips curving. I didn't notice until after it was dry. - A template that was slightly smaller than the hole was made. After marking out the location in pencil, I used the table saw (in a dodgy way that I probaly won't try again without a better setup) to cut out most of the waste. - Big Daddy to the rescue! This bit just paid for itself. It worked brilliantly to follow the template. I had a vacuum from underneath and 4" pipe sucking dust and chips away. I might need to make some inserts to keep the timber out of the router. I need to spend some more time sanding and scraping underneath the board. I've sanded to 80grit on the top and bottom, rounded the corners and edge, and filled in some cracks with epoxy to leave overnight. I'll sand some more tomorrow and hopefully get some oil on it tomorrow afternoon. There's one part I'm slightly sad about, you might pick it up if you've got a keen eye. 2 Quote
Brendon_t Posted September 21, 2017 Report Posted September 21, 2017 Very cool. I made a big ol 40" wide cutting board a while ago to span to sinks in a boat. Relief carved the bottom to drop down in the basin like you did the range hole. I'm assuming you made the board too short and had to add the solid color strip to the end was the booboo? Quote
lewisc Posted September 21, 2017 Author Report Posted September 21, 2017 38 minutes ago, Brendon_t said: I'm assuming you made the board too short and had to add the solid color strip to the end was the booboo? Yep. I should've looked for a piece that didn't have so much red in it. I'm hoping it doesn't stand out too much when oiled. 40"? That's a big one. Got a picture? Quote
wdwerker Posted September 21, 2017 Report Posted September 21, 2017 I would use Lexcel clear caulk , not silicone. Might take 2-3 days to dry but it will look better and last much longer. Quote
lewisc Posted September 21, 2017 Author Report Posted September 21, 2017 Thanks Steve. I'll let her know as it's her husband that will be installing it. Do you know if would stick to a mineral oil finish? Do you think it would be best applied after the board is in place? Quote
wdwerker Posted September 21, 2017 Report Posted September 21, 2017 I would mask off the top and caulk it in place, Lexcel cleans up w mineral spirits, pull the masking immediately after caulking and then let caulk dry 2-3 days before applying the mineral oil. I would set the board about 1/8 above the countertop so that any water won't soak in and any juices from the board would run off. This would also let the board be scraped or sanded periodically to reduce knife marks. Plus exactly flush can be very hard to achieve. 1 Quote
Popular Post lewisc Posted September 22, 2017 Author Popular Post Report Posted September 22, 2017 And done! I was asked to oil it before installation so it's out of my hands if it doesn't stick. It's heavy though so the weight will keep it in place at least. Oiling really is the best part so I was also happy to see the colour. The colour matches well enough and my 'client' is happy. It sits about 15mm above the counter with 30mm below. The pics are: Sanded to 240grit - I need to get better at masking the epoxy. Mineral oil - Inside lighting Mineral oil - in the sun 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.