Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Grounding issue on Delta Rockwell cord rewire

Featured Replies

I wired a new cord into the switch same way it was wired before with ground wire connected to switch box. But now when I connect the switch box to the saw frame and plug it in, it blows the gfci outlet fuse without even turning it on. When I disconnect the ground from switch box it works fine. Any ideas?

WIRING1.jpg

WIRING2.jpg

I'd use a multi-meter with a continuity check to find where the short is. Work your way from the saw forward. I wouldn't use plugging it into the outlet as a test. GFCI's trip by there being an uneven amount of current between the hot and neutral you have some electrical pixies catching the ground somewhere. Odds are it's inside that metal box.

Agreed with Chestnut. A dvom will be your best bet.  You're looking for a closed circuit across the hot and neutral.  Hopefully it's in the new plug and not in the winding but if it runs fine before, probably a wiring oops.

  • Author
5 minutes ago, Brendon_t said:

Agreed with Chestnut. A dvom will be your best bet.  You're looking for a closed circuit across the hot and neutral.  Hopefully it's in the new plug and not in the winding but if it runs fine before, probably a wiring oops.

Ok, yeah good suggestions, I haven't had much experience with doing a circuit test.  I'll have to do some research  Thanks

 

18 minutes ago, Brendon_t said:

Agreed with Chestnut. A dvom will be your best bet.  You're looking for a closed circuit across the hot and neutral.  Hopefully it's in the new plug and not in the winding but if it runs fine before, probably a wiring oops.

Well if it's popping the GCFI and not the breaker it's not necessarily between the hot and neutral. That would be a hot to neutral short this has to be a fault to ground where either the hot or neutral is contacting ground. IIRC GFCI's don't trip on total amps drawn just the differential between hot and neutral. If it was a hot to neutral short the GCFI wouldn't trip because the current on the 2 legs would be equal.

You'll want to test parts of the circuit to make sure there are no connections to ground.

Just now, Chestnut said:

Well if it's popping the GCFI and not the breaker it's not necessarily between the hot and neutral. That would be a hot to neutral short this has to be a fault to ground where either the hot or neutral is contacting ground. IIRC GFCI's don't trip on total amps drawn just the differential between hot and neutral. If it was a hot to neutral short the GCFI wouldn't trip because the current on the 2 legs would be equal.

You'll want to test parts of the circuit to make sure there are no connections to ground.

Yeah op, go with that. I'm on my ~3rd day next to no sleep.

9 minutes ago, Brendon_t said:

Yeah op, go with that. I'm on my ~3rd day next to no sleep.

Get some sleep man! Not not wrong just so you know a short will still probably trip them.

  • Author

So apparently I was wrong and I think its just an outlet with over current protection..and not GCFI ? Not sure if that changes what you think...

3 minutes ago, Alex Fountain said:

So apparently I was wrong and I think its just an outlet with over current protection..and not GCFI ? Not sure if that changes what you think...

This is something I've never seen. I'd check for short circuits everywhere then. idk what the resistance through the motor should be but i'd check that as well.

Be aware the it may not be a direct short circuit. It could be a high resistance (up to 24,000 ohm) short between the hot & ground or the neutral & ground. It only takes around 5 mA to trip a GFCI. Chances are very good that the problem is in the motor where there's a lot of wire that only has a very thin layer of varnish for insulation. Sometimes a standard multi meter won't find the fault because they use only a very low voltage to measure resistance. It might look good until 120V is applied. A high voltage insulation tester (Megger) will tell you what's really going on.

I should add the going without a ground connected would be particularly dangerous here. It's already known that there is a low level fault there & disconnecting the ground could leave you with a saw that has a 'hot' table some day soon.

Did you draw schematic using the old cord? Obviously, there is something wrong. If you are not sure of what to do with the multi-meter (get one at Harbor Freight free with a coupon and purchase), get someone that has the knowledge to proper use it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.