Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Harbor Freight Long Reach Magnetic Pickup Tool with Quick Release

Featured Replies

  • Popular Post

https://www.harborfreight.com/long-reach-magnetic-pickup-tool-with-quick-release-93950.html

Some recent threads on grinders reminded me.  I bought one of these last spring and it's been very useful for cleaning steel dust from the floor around my grinders.  The magnet is pretty strong.  After you pick up some dust you can take it to the garbage can, pull the ring and release the dust into the can.  Yeah, I could just drag the vacuum from the other side of the room fuss with the hose, unwind the cord and just suck up the dust.

  • Popular Post

That's a pretty neat tool. I've been using one of the big round magnets on the end of a small broom handle thing. I just slip a plastic bag over it and when I'm done picking up all of the stuff, I just pull the bag off. Most of the time it's picking up screws and nails that I've dropped.

  • 4 weeks later...

I picked one of these up and it's very useful for finding screws I've dropped into shavings.

I keep a tape measure and a magnet in my shop apron, and that works for screws and what not.  I just had a wall cabinet fall down when the french cleat failed, and it spilled a bunch of white board pens all over the floor.  I got the grabber from the car toolkit to pick up the non-magnetic pens.

 

Grabber.jpg

On 8/7/2025 at 8:15 AM, Beechwood Chip said:

I just had a wall cabinet fall down when the french cleat failed...

Yikes! As a french cleat user, any lessons learned?

  • Popular Post

It's not as bad as it sounds.  I was storing a rolled up glue mat under the cabinet, so it just tilted forward about 20 degrees, and dumped some of the stuff that I had on top of the cabinet on the floor.  It looks like the screws pulled out of the brick.  The brick is pretty soft and crumbly.  It's a 140 year old brick house, and it seems that they used a harder brick for the exterior layer and then a softer brick for the interior layers.

I'll probably just use twice as many screws next time.

 

  • Popular Post

Got a chance to check it out (it's been a crazy few days).  This was my father's old tool chest that he made "when he was a young man".  It was slapped together out of whatever he could find on the street.  The case was from an old sewing machine.  The drawer "slides" are just strips of wood in dados. They stick, and then the drawer pulls pop out of the drawer.  Whenever he saw it in my shop, he'd say, "If I knew how long it would be around, I'd have made it better."

The back was hardboard and I screwed and glued the french cleat to the back.  The cabinet case was too thin for me to get screws into.  I used two french cleats, but I guess only the top one was really taking the weight.

Anyway, the screw heads pulled right through the hardboard.  Then the bottom cleat held and the cabinet pitched forward, and came to rest on the stuff I had under it.  

So, now I have to decide whether to reinforce it and put it back, build some sort of stand to support it, or just buy a replacement.  On the one hand, it was never intended to be a permanent solution and even if I give it a thorough renovation, it'll still be wonky.  On the other hand, it's my father's tool chest that I grew up with, where I learned the names and locations of all the tools.

So, I guess I'll replace the drawer pulls and wax the runners and build a stand for it to sit on.  

 

 

  • Popular Post
On 8/7/2025 at 10:34 PM, Coop said:

@Beechwood Chip, is the interior brick just in your shop or throughout your house? I bet that looks neat! 

The house structure is brick.  I think it's four courses thick in the basement, and probably two on the 3rd floor.  When William Penn founded Philadelphia he remembered the London fire, and wanted the city built from brick, not wood.  Plus, there was lots of good clay around Philly.  Penn would pay a bonus to any brick maker or bricklayer who wanted to immigrate.

But the interior is all plaster, even in the basement.  When I want to anchor to it, I drill through the plaster and into the brick, and then use an anchor.  I tried using Tapcons at first, but the brick was to crumbly for the Tapcons to hold reliably.  My procedure is to drill a hole, blow it out with compressed air, dip a plastic anchor in epoxy and push it in, and then screw.  If I'm being careful, I let the epoxy cure before adding weight.

There are a couple places where the brick is exposed, but it's not very attractive.  Rough, uneven bricks and thick, clumsy mortar lines.  That's when I learned that there's exterior brick that can stand up to weather and looks nice, and cheap brick for internal courses or places where it won't show.  At least, that was the case around 1880.

But the exterior brick is amazing.  Razor thin mortar joints, and the mortar was stained black .  There's a couple of rows of ornamental brick way up near the 3rd floor.  The brick on the back of the house is less fancy, but serviceable.  Philly was famous for it's brick work at one time.  Walking around the older parts of town you can see some really nice brickwork.

On 8/7/2025 at 8:54 PM, Beechwood Chip said:

So, now I have to decide whether to reinforce it and put it back, build some sort of stand to support it, or just buy a replacement.  On the one hand, it was never intended to be a permanent solution and even if I give it a thorough renovation, it'll still be wonky.  On the other hand, it's my father's tool chest that I grew up with, where I learned the names and locations of all the tools.

So, I guess I'll replace the drawer pulls and wax the runners and build a stand for it to sit on.  

I completely get having attachment to something and this certainly sounds deserving. I would enjoy looking at family history like this when working in the shop.

As I understand its construction, a stand or a french cleat shelf (e.g.) that supports the chest from the base seems like the prudent course.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.