Popular Post Mark J Posted November 28, 2025 Popular Post Report Posted November 28, 2025 I have a project going that needed some bandsaw work with a different blade. I find blade changing to be a real PITA, especially readjusting the guides. I labored through the process, including adjusting the upper and lower guide bearings. After I finally got the guides adjusted perfectly I set up for the cut. Since it was a tall cut, I raised the guide post about 12 inches, etc. Then just as I was about to begin, I noticed that the upper guides were no longer aligned. The thrust bearing had moved a good 2 mm back from the blade as had the side bearings. I cranked the guide post down and sure enough the upper guides were aligned. Raised the post again and the upper guide was again off. To keep the project going I readjusted the uppers with the post raised, and made the cut. Then I came back to look at the saw. First I confirmed the blade is staight and perpendicular. Then readjusted the guide in the low position. No gap. Raise the post and there's a gap. and with a square I called Tech Support at Jet. The technician told me the post could be adjusted. There are four set screws, each secured with a nut and lock washer. I loosened the nuts on the lock washers, then maybe a quarter turn of the upper two set screws brought the post into fore & aft alignment. Of course, now that I look at it carefully, I see the guide post is out of alignment laterally by maybe the thickness of a piece of paper. Not sure I'm going to chase that. Has anyone else had a problem with guide post alignment (or even looked). I suppose one solution is to set the guide post height before adjusting the guides. 6 Quote
gee-dub Posted November 28, 2025 Report Posted November 28, 2025 Glad there were adjustments to correct the path of the post. My little Rikon had a guide post travel path issue right out of the box. It was left to right as opposed to front to back. It is a pretty unsophisticated system that is really just an aluminum extrusion riding against the sheet metal housing; no adjustments. Turned out the extrusion was out of true. Rikon replaced it quickly and without a lot of fuss so kudos to them. There was still a bit more deviation than I was happy with but I was able to tweak the edge of the housing where the extrusion rides and got it very workable. Of course the post only moves a little more than 4" so the deviation and correction were pretty small. My 17" machines are adjustable similar to yours. When I am doing machine setup I find (mostly due to my personality) that I just plan to do nothing else. Sometimes it takes half an hour, sometimes hours. Depends what the machine is and why you are aligning it. I just don't like being distracted by the clock when I am in the middle of machine setup. The extra time you take when aligning a machine will pay dividends every time you use it. 2 Quote
Von Posted November 28, 2025 Report Posted November 28, 2025 You made me curious so I checked my bandsaw today. I see about 1mm change, mine getting closer to the thrust bearing towards the top. It appears I have some set screws to make adjustments and I'll play with it sometime I have a little more time. 1 Quote
Popular Post Gary Beasley Posted November 29, 2025 Popular Post Report Posted November 29, 2025 I found a similar problem on my Grizzly bandsaw and solved it with a bit of shim under the riser extension block. 3 Quote
Popular Post JustAnotherGuy Posted December 17, 2025 Popular Post Report Posted December 17, 2025 On a lot of saws the guide post isn’t perfectly square through its full travel, so the guides shift as you raise and lower it. You already found the real fix by tweaking those set screws. Most folks never notice because they set the guide height first and then adjust the guides. That’s usually the best workflow going forward. If the lateral misalignment is only paper-thin, I’d personally leave it alone and get back to cutting. You’re definitely not alone on this one. 4 Quote
Jfitz Posted December 20, 2025 Report Posted December 20, 2025 My saw is currently taken apart so I can replace the drive belt which decided to melt and shred today. Ugh. I had set it up yesterday for some resawing I wanted to do today, and it was as good as I have gotten it. At least, until I turned it on this morning. New belt is on the way but won't be here till Monday. Since apparently I have free time on my hands, I'll check out the post alignment on mine, mostly out of curiosity. 2 Quote
Popular Post Jfitz Posted December 20, 2025 Popular Post Report Posted December 20, 2025 On 12/20/2025 at 12:47 PM, Jfitz said: I'll check out the post alignment on mine, mostly out of curiosity. surprisingly it's almost spot-on. Who knew! 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.