Calix Posted August 29, 2011 Report Posted August 29, 2011 Greetings everyone! I recently bought a new Record #7 jointer handplane, unfortunately the blade is off square. I've been looking for some information I can use to fix this inconvenience but I can't find anything about the subject. Is there a solution for this? (Resharpening, regrind). Definetly, buy a new blade? I did all the tune up work and I am already using the plane, it works, but I know having a square blade means a better performance. I ask for your help and expertice guys, what is the way to go? Thanks! Quote
Dan S Posted August 29, 2011 Report Posted August 29, 2011 How far out of square are we talking? Quote
duckkisser Posted August 29, 2011 Report Posted August 29, 2011 might be able to just sharpen it square depending on the company alot of times the blades are bought at the right degree but not honed to a perfect edge like i want. and congrats on geting a #7 i want one but have no use for one so i cant convince myself that i need one. just so you know i found two small hand planes siting in the trash with lots of other tools. yaye me. Quote
Calix Posted August 30, 2011 Author Report Posted August 30, 2011 How far out of square are we talking? Hi Dan. I'd say by as much as 0.75mm Do you think it can be ignored? Am I exagerating? Quote
Calix Posted August 30, 2011 Author Report Posted August 30, 2011 might be able to just sharpen it square depending on the company alot of times the blades are bought at the right degree but not honed to a perfect edge like i want. and congrats on geting a #7 i want one but have no use for one so i cant convince myself that i need one. just so you know i found two small hand planes siting in the trash with lots of other tools. yaye me. Hi there! I wasn't sure about buying this handplane, but now I know it was money well spent. I just needed to give it a try, milling boards by hand is hard work, but I've been practicing a lot, and after a while I must say I find it quite enjoyable, and it is a heck of a great upper body workout. I wish I could find tools in the trash About the edge of the blade, I am thinking about grinding the blade on sandpaper so I can get a nice square edge. I did it once with a chisel to get rid off a nick on the edge. I just don't know if this could work for a handplane blade. Quote
Dan S Posted August 30, 2011 Report Posted August 30, 2011 Hi Dan. I'd say by as much as 0.75mm Do you think it can be ignored? Am I exagerating? You could probably get by with it, but if it's only off that much you can regrind it pretty easily. Personally I would regrind it, just for the peace of mind. Quote
jhl.verona Posted August 30, 2011 Report Posted August 30, 2011 Most of the planes I bought second hand (two #5's and a #7) had blades which were slightly off square. One even more than yours. I used plenty of 180 grit sandpaper on a marble tile, and an eclipse honing guide similar to this one (the one at the bottom of the first photo, also the third photo). It takes a while, and some sandpaper, but I don't have a grinding wheel. In any case the results were worth the effort. The #7 is an excellent tool for preparing flat surfaces, so I'd keep the blade square if I were you. John Quote
jwatson Posted August 30, 2011 Report Posted August 30, 2011 if you are using its probably not all that bad a deal. you can regrind and hone and get it square. I wouldnt bother if its usable. later on you can save up and get a hock iron. Quote
wilburpan Posted August 30, 2011 Report Posted August 30, 2011 Hi Dan. I'd say by as much as 0.75mm Do you think it can be ignored? If you can get an even full width shaving, then you're in good shape. Eventually you'll want to square up the blade, but it's not an emergency right now. The easiest way of squaring up your blade is to put the blade into your favorite sharpening jig, use spray adhesive to glue a piece of 80 grit sandpaper to a flat surface like a piece of granite or glass, and go to town on the blade. Then sharpen it like you normally would. Quote
Calix Posted August 30, 2011 Author Report Posted August 30, 2011 Most of the planes I bought second hand (two #5's and a #7) had blades which were slightly off square. One even more than yours. I used plenty of 180 grit sandpaper on a marble tile, and an eclipse honing guide similar to this one (the one at the bottom of the first photo, also the third photo). It takes a while, and some sandpaper, but I don't have a grinding wheel. In any case the results were worth the effort. The #7 is an excellent tool for preparing flat surfaces, so I'd keep the blade square if I were you. John Hi. Unfortunately I don't have a honing guide, so I will keep using the blade as it is, at least until I get the honing guide, but I will definetly try the sandpaper, I hope soon. Grazie John! Quote
Calix Posted August 30, 2011 Author Report Posted August 30, 2011 if you are using its probably not all that bad a deal. you can regrind and hone and get it square. I wouldnt bother if its usable. later on you can save up and get a hock iron. Hi JWatson! Thanks for the advice! I didn't know about the Hock blades! I visited their Web Page and those blades look like really fine metallurgical craftsmanship. I'm sure gonna get one of those plane irons. Thanks! Quote
Calix Posted August 30, 2011 Author Report Posted August 30, 2011 If you can get an even full width shaving, then you're in good shape. Eventually you'll want to square up the blade, but it's not an emergency right now. The easiest way of squaring up your blade is to put the blade into your favorite sharpening jig, use spray adhesive to glue a piece of 80 grit sandpaper to a flat surface like a piece of granite or glass, and go to town on the blade. Then sharpen it like you normally would. Hi Wilbur! As you say, it is not an amergency, so I will wait for my new sharpening jig and get that 80 grit sandpaper. I can imagine putting more pressure on one side of the blade so it will get even with the other and finally get it square right? Or maybe I just have to concentrate on the lapping and the jig will do the rest? Thanks! Quote
Roger T Posted August 30, 2011 Report Posted August 30, 2011 Are you sure the sides of the blade are parallel? Some irons are not parallel, and if you are checking with a square, then it will show as being out of square. Just a thought. Roger Quote
wilburpan Posted August 30, 2011 Report Posted August 30, 2011 Hi Wilbur! As you say, it is not an amergency, so I will wait for my new sharpening jig and get that 80 grit sandpaper. I can imagine putting more pressure on one side of the blade so it will get even with the other and finally get it square right? That will work, over time. This sort of thing is hard to do freehand, which is why I would do this with a sharpening jig of some sort. Usually when I sharpen I do it freehand, because it's faster than lining up the blade in a jig. But for major rehab, I'll use the jig. Again, it's not an emergency. If the plane gods had wanted us to have perfectly square blades, they would not have invented lateral adjusters. You just have to have a blade that is square enough. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.