davestanton Posted October 13, 2011 Report Posted October 13, 2011 A video I put together about the charging station I built after watching Marc's video on his own CS. While I was at it, I thought I would run through the Battery tools I have as well. http://www.youtube.com/watch?v=ZrIOCKN7LhM Quote
Jfitz Posted October 13, 2011 Report Posted October 13, 2011 Nice video Dave. I don't have nearly that many battery-operated tools, but it does get me thinking about having a better organized charging center for both my shop AND for the kitchen (cell phones, iPads, handheld game systems, etc). Too many cords and chargers laying about (kitchen), or too uch time spent looking for the charger and a place to put it while plugged in. Quote
over40pirate Posted December 22, 2011 Report Posted December 22, 2011 Imho, the most important part of a charging station is a timer. I used a 1hr spring wound timer from the Borg. ($15) Leaving batteries on a charger can lead to an early failure. Sorry, no video! Quote
PaulMarcel Posted December 22, 2011 Report Posted December 22, 2011 Did the same as Pirate... have a board at the end of my bench with 5 duplex plugs; 3 are on a bathroom fan timer (different color plugs). I also notice that leaving a battery in the charger even when it isn't plugged in seems to drain them a bit. In my case, it is by the shop door so when I see a battery in there and the charge light is off, I pull it out. Quote
konkers Posted December 28, 2011 Report Posted December 28, 2011 I also notice that leaving a battery in the charger even when it isn't plugged in seems to drain them a bit. I've noticed this as well. I managed to kill one of the batteries to my Rigid drill by doing that. Quote
Beechwood Chip Posted December 28, 2011 Report Posted December 28, 2011 I don't think you need to worry about leaving a battery in a "smart" charger, only "dumb" ones. I try very hard to only use "smart chargers", the ones that can charge a battery in an hour or so. As I understand it, If you charge a battery fast when it's full, it can explode, so "dumb" chargers use a slow rate that is safe for a full battery, and have warnings that you should stop charging after six hours. "smart" chargers measure the charge so they can charge fast, and stop when the battery is charged. Then they just put in a "trickle" to keep the battery topped off as it loses charge over time. The dumb chargers need an external timer to keep from over-charging, but the smart chargers have over-charging protection built in. I may have this wrong, and it may be different for batteries with different chemistries. Quote
ChetlovesMer Posted December 29, 2011 Report Posted December 29, 2011 Chip, you are not wrong. You are, in fact, %100 right. The dumb charger and smart charger thing is a fact. Most newer tools come with smart chargers today. Especially if they are Lithium-ion batteries. One of the nice things about lithium-ion technology is that it can in fact be charged very quickly. Therefore, the smart charger is almost a necessity. You can tell you have a smart charger if it has a blink code. When the charger starts telling you the battery is full, it stops filling it. The same is usually true for Nickel-Metal-Oxide batteries, although those tend to be rare batteries, I think only some Makita tools and Panasonic ever really went with that technology. Most Nickel-Cadmium batteries tended to have dumb chargers. Nickel-Cadmium batteries, in addition to weighing more are, in general, are far more finicky. They don't like over charging, they don't like changes in temperature, they tend to wear out over time, even under the best conditions. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.