davestanton Posted December 22, 2011 Report Posted December 22, 2011 Hi guys. I am being exposed to new tools at this new gig I have and they tell me that the 2000 watt triton router is THE router to use if you want to make a router table. The main reason being that it has its own lift mechanism and that saves you having to buy a router lift to cradle it in. It also has a variable speed motor and good dust shroud. Can anyone give me their thoughts on this router as it appears to be about 1/5th the price of the Festool 2200? Quote
woodhack Posted December 22, 2011 Report Posted December 22, 2011 Best thing I ever did was permanently mount that sucker in my portable router table. It's a beast and the micro-adjust is as good as any router lift and WAY better than the PC 895. The only "negative" (and this isn't much of one unless you're lazy like me ) is that I wasn't able to find a pre-drilled mounting plate for my table so I had to make my own. Well worth the extra half-hour of time to have a router this good in my table. Quote
dwacker Posted December 22, 2011 Report Posted December 22, 2011 Id say they are ok but thats about it. I went through two on them in 2009 in less than a month doing cabinet door when my shaper was in the shop. Never did get them warrantied because the company was in receivership. Personally id just stick with the 3 1/4 pc and real lift. If you use it alot you have to keep it clean or it binds. Quote
Beechwood Chip Posted December 22, 2011 Report Posted December 22, 2011 I've heard that some models of the Triton with the built in lift have an interlock which turns the switch off when you raise the collet into "bit change" position. You have to flip the switch to turn it back on. This is a pain when the router is permanently mounted under your router table in an enclosed cabinet and permanently plugged into a table mounted power switch. I don't know if they have changed their minds on that one, but I think it would seriously interfere with "THE router to use if you want to make a router table" status. Quote
weedsnager Posted December 23, 2011 Report Posted December 23, 2011 I've heard that some models of the Triton with the built in lift have an interlock which turns the switch off when you raise the collet into "bit change" position. You have to flip the switch to turn it back on. This is a pain when the router is permanently mounted under your router table in an enclosed cabinet and permanently plugged into a table mounted power switch. I don't know if they have changed their minds on that one, but I think it would seriously interfere with "THE router to use if you want to make a router table" status. this is the one main problem with this router mounted in a table and using an external switch. there was a diagram on another website on taking out the switch cover, but i couldn't figure it out. Quote
knotscott Posted December 23, 2011 Report Posted December 23, 2011 Most comments I've read from owners about the Triton are positive. The Freud FT3000 and FT1700 also have built in lifts with a host of above table features that allow easy one handed topside bit changes. Quote
Dave Posted December 23, 2011 Report Posted December 23, 2011 I have the Triton 2 1/4HP bolted under the benchdog cast iron TS wing, enclosed with a modified Powermatic router cabinet (Detla TS). The Triton bolted directly to the BD insert without modifications. I've had the Triton three or four years and has only given me minor problems. I've been pretty rough on it even using it to route aluminum plate. I have had to take it apart because wood chips got in the lifting gears and would not let it plunge all the way to activate the collet lock when changing bits. Overall it's been a good router, the above the table depth changer works well. One thing i really like is being able to change the bits with one wrench above the table. If you are hand routing with it the depth stops are clunky and the dust/chip collection doesn't work very well. Also sometimes the little sliding door over the power switch is a PITA. Quote
tdale51@yahoo.com Posted December 24, 2011 Report Posted December 24, 2011 Thanks for the tip! I've been looking to have a separate router I can leave in the table and this seems to fit the bill exactly! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.