mr.joshq Posted January 20, 2012 Report Posted January 20, 2012 So I'm just getting back into this awesome hobby with the help of Marc's podcasts. I've got an OLD (1965) craftsman table saw(may or may not be square), drill press, router table, and access to a small (5") jointer, miter saw, older delta scroll saw, shop built drum sander, shop built dust collector, half built shop built panel saw, small douglas fir bench and various hand tools. I just got about $400-500 to spend on a new piece of equipment. I'm looking at a few options with that. First, I don't have a bandsaw and am looking at a couple of 14" in the price range (all seem to be a variation on the Steel City Taiwan made one) since I don't have one yet. I need to replace my table saw, as it is very frustrating trying to get an accurate and repeatable cut from it(table itself actually isn't square). But for my budget I think i'm better off waiting to purchase something in the 800-1000 range. I have access to a small jointer, but I'd like to upgrade to a 6" or more that actually lives in my shop. I can get a deal on one for about 300 and that with a small (12-13") planer would also fill my budget. So far I haven't done much with rough lumber (hard to get around these parts for some reason, considering I'm in lumber central MN.. but it's all pine) My router(not plunge) and router table(small craftsman) could stand to be upgraded as well. I'm of the opinion so far that if I have something, I should wait to replace something until my compliment basic machines are complete (TS, BS, Jointer, Planer, Drill Press, Router Table). How would you guys prioritize your tools for the beginner? Quote
Beechwood Chip Posted January 20, 2012 Report Posted January 20, 2012 Here's the best answer I've seen to that question. I've had bad experienced buying tools because I should, or because I saw a good deal. I've had good experiences buying a single tool that I had an immediate need for. 1 Quote
duckkisser Posted January 20, 2012 Report Posted January 20, 2012 get at least 6in jointer 8 is better don't bother with the bench top 4 inch ones they're too light and not strong enough. a contractor table saw is fine for now and probably for the rest of your life depending on what you make. i prefer the 13 in dewalt planer its not too bad a price and it is a dependable work horse. and start thinking of a good dust collection system you will make lots and lots of dust and chips so cleaning it up from the start is a must. i would like to see your drum sander and dust collector always like to see any shop built ones. keep a eye out on craigs list and the newspaper and buy what you need as you need it. use my table saw a lot and just about every cut that you do in the shop can be done on a table saw with some planed jigs and sleds. Quote
areynoldsre Posted January 21, 2012 Report Posted January 21, 2012 You need to answer this question first: what kind of projects are you going to do? +10 to Beechwood's answer. Quote
Beechwood Chip Posted January 25, 2012 Report Posted January 25, 2012 +10 to Beechwood's answer. It's Rmac's answer - I just linked to it! Quote
areynoldsre Posted January 25, 2012 Report Posted January 25, 2012 It's Rmac's answer - I just linked to it! Still - ++ for being smart enough to link to it. Quote
Rowdymon Posted January 25, 2012 Report Posted January 25, 2012 I"m not all that experienced... However I would suggest first looking at your table saw. You said it may or may not be square...tune it up, see if you can get it working properly. I know there are video's on Marc's blog and more articles than I care to count on that topic. Because...if you go purchase a table saw...you are still going to have to do that. It won't be square and tuned up when you purchase it. If you can get the miters squared to the saw but not the fence...spend a little money and get an after market fence, link belt, etc..etc.. Then see what you have left over. THey are skills you are going to need, why not practice them on what you have? That's how I would personally go about it... Quote
over40pirate Posted February 3, 2012 Report Posted February 3, 2012 If your ts is working good, I would first buy a Delta T2 fence for it ($155) Then I would buy a Rigid oss, and look for a nice used Delta 14" band saw. Older the better. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.