Recommended Posts

Posted

It seems like Festool is missing a valuable opportunity by not producing their dominos in wider widths to accommodate the +6 and +10mm settings. what a nice tenon one could have given the aforementioned opportunity.

Posted

The 700 makes slot sizes 8, 10, 12, 14 mm with a maximum depth of 70 mm

right, but they still don't make extra wide dominos to my knowledge. the only make dominos for the "exact fit" setting but not the wider settings.

Posted

I get what your asking and think its a pretty logical question. I think were just going to be stuck making our own. Im sure the logic is that if they made all the sizes that it would be to costly to manufacture.

Don

Posted

What i think he is talking about is the odd sizes or sloppy fit sizes for lack of a better term. The exact fit is the only size available but the machine cuts 6mm and 10 mm wider. So why not make for example 5mm thick in 19, 23 and 29 wide.

Don

Posted

Thanks dwacker! Good to know that I have an alternative source of dominos. I am planning to set up and make a quantity of wider dominos in a couple of thicknesses and several widths. I think a coarse paper in my drum sander should give me a surface texture for glue to flow. Has anybody done much of this domino making and have any tips or suggestions? I was planning on using scrap maple.

Steve

www.steveduncan.com

Posted

What i think he is talking about is the odd sizes or sloppy fit sizes for lack of a better term. The exact fit is the only size available but the machine cuts 6mm and 10 mm wider. So why not make for example 5mm thick in 19, 23 and 29 wide.

Don

yes, this is exactly what im talking about. i guess i could just make my own, but honestly, my laziness impedes me from doing so. it just seems like such an easy opportunity for festool to cash in on different sizes.

Posted

Thanks dwacker! Good to know that I have an alternative source of dominos. I am planning to set up and make a quantity of wider dominos in a couple of thicknesses and several widths. I think a coarse paper in my drum sander should give me a surface texture for glue to flow. Has anybody done much of this domino making and have any tips or suggestions? I was planning on using scrap maple.

Steve

www.steveduncan.com

Ive made loose tenons for years. Before the domino I used a slot mortiser. Once you get the setup right they are very easy. Rip your stock, round the sides and then cut two very shallow 1/8" dados the length of the tenon for glue to flow. Its much easier to make them in long lengths like 6 ft then just chop off what you need when you need it.

Don

  • 2 weeks later...
Posted

I made my first batch of wide domino's last Friday! I ripped 9mm thick strips from off-cut waste red oak and sanded them to 8mm on my drum sander using 80 grit. You could probably plane them if you don't have a drum sander. I was careful to sneak up on a nice fit ,not too tight to scrape off the glue when assembling. The 80 grit leaves a bit of texture for glue relief. I ripped the strips to the width of the small, medium and largest width settings and used a 3/16 radius round over bit in the router table . I set up a feather board on the top and sideways for a safe and consistent route on the corners. I made strips about 3 ft long for easy handling. Once I was set up it went pretty quick. I made 2 dozen strips which should hold me for awhile. Going to cross cut them on the bandsaw as needed.

I plan on trying Cincinnati dowel's domino's 5mm x 30mm Oak Tuffer Tenons. 1800 cost $56 with free shipping. I have no intention to make vast quantity of tiny accurate parts. But I can have control of the width , length and how tight the fit is for special situations. I plan to make a batch of 5 and 6mm stock in all 3 widths next. I think 1 wide domino in the corners of glass door frames will add extra strength to the cope and stick joint without a lot of effort

My reason for making my wide domino stock is a 4ft by 8ft multi-panel barn door for a client. I wanted more strength and resistance to flex when gluing up 12 cope and stick joints to make a 5 panel door

Steve Duncan

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 44 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined