Fricasseekid Posted October 17, 2012 Report Posted October 17, 2012 I don't know if it runs. I'm going to look at it this evening. But it's only $195. I figured at that price I could just rebuild the machine. This is my first jointer, any advice would be appreciated. Quote
STL Woodguy Posted October 17, 2012 Report Posted October 17, 2012 I don't know if it runs. I'm going to look at it this evening. But it's only $195. I figured at that price I could just rebuild the machine. This is my first jointer, any advice would be appreciated. It definitely needs some major TLC but if it runs, the tables just need the rust removed and are flat and the unit doesn't need 'too' much repair, I absolutely would have been all over an 8" Delta for that price. I don't think it'd hurt to check it out at the least. Quote
knotscott Posted October 17, 2012 Report Posted October 17, 2012 For $195 that'd be a heck of a buy if it's salvageable. Quote
rodger. Posted October 17, 2012 Report Posted October 17, 2012 If it doesn't work out, the metal alone in that machine will return some of your investment. Quote
Fricasseekid Posted October 17, 2012 Author Report Posted October 17, 2012 Thanks guys. Even if its in real bad shape I may just make a low ball offer and buy parts for it. I'll keep you posted. Quote
Fricasseekid Posted October 17, 2012 Author Report Posted October 17, 2012 Ok, so the in-feed table seems to operate fairly well and the machine runs! But it has lots of bad vibrations and the out-feed table seems froze. It's definitely gonna need a new cutter head and lots of TLC. I got it for $160. Did I make a mistake? Quote
STL Woodguy Posted October 17, 2012 Report Posted October 17, 2012 For the vibrations, I'd probably look first at replacing the belt and getting the tension just right (doesn't have to be as tight as you might think). Something like this may do the trick and is versatile... http://www.rockler.c...CFWaoPAod62oA5w ...and I think Harbor Freight carries some sort of clone that I've heard good about. You also want to make sure the pulley on the cutterhead is in line with the pulley on the motor. If those two are out of whack, that will certainly cause more noise and vibrations. Why does it need a new cutterhead, beat up? Or just needs new blades? The latter is a much cheaper venture than the former. But even with cutterhead replacement, I'd look to see if the current DJ-20 cutterheads will still fit the older ones. Or hunt online for a replacement. Worst case scenario, buy a spiral head cutter. Expensive, but is essentially an upgrade to the unit. (I'd solve the other issues before doing this, though.) Outfeed table, tough to say...rusted maybe? My outfeed seemed stuck on the used Powermatic I bought, but I think a gib bolt was too tight or something. Mine has dovetail ways, so once I got it freed, I took them off and cleaned it out real good, waxed the ways with lithium grease, and they work great now. Even if stuck forever, it's the infeed table that will require more up-and-down adjustment, so if you can get the infeed - and cutter blades - perfectly parallel with the outfeed, you're good. Quote
JayWC Posted October 18, 2012 Report Posted October 18, 2012 Even if stuck forever, it's the infeed table that will require more up-and-down adjustment, so if you can get the infeed - and cutter blades - perfectly parallel with the outfeed, you're good. Yeah but...you need the outfeed table to move in order to set the height even with the top of the blades or you'll never make straight wood out of the machine. Quote
Fricasseekid Posted October 18, 2012 Author Report Posted October 18, 2012 For the vibrations, I'd probably look first at replacing the belt and getting the tension just right (doesn't have to be as tight as you might think). Something like this may do the trick and is versatile... http://www.rockler.c...CFWaoPAod62oA5w ...and I think Harbor Freight carries some sort of clone that I've heard good about. You also want to make sure the pulley on the cutterhead is in line with the pulley on the motor. If those two are out of whack, that will certainly cause more noise and vibrations. Why does it need a new cutterhead, beat up? Or just needs new blades? The latter is a much cheaper venture than the former. But even with cutterhead replacement, I'd look to see if the current DJ-20 cutterheads will still fit the older ones. Or hunt online for a replacement. Worst case scenario, buy a spiral head cutter. Expensive, but is essentially an upgrade to the unit. (I'd solve the other issues before doing this, though.) Outfeed table, tough to say...rusted maybe? My outfeed seemed stuck on the used Powermatic I bought, but I think a gib bolt was too tight or something. Mine has dovetail ways, so once I got it freed, I took them off and cleaned it out real good, waxed the ways with lithium grease, and they work great now. Even if stuck forever, it's the infeed table that will require more up-and-down adjustment, so if you can get the infeed - and cutter blades - perfectly parallel with the outfeed, you're good. First off, thanks for sharing. Some good info here. I think the primary issues with this machine will be rust related. It is ate up with rust. That is why I believe it will need a new cutter head. The entire cylinder and blades are inundated with rust. I was thinking of picking up a spiral head in case I do have to replace it. Quote
STL Woodguy Posted October 18, 2012 Report Posted October 18, 2012 I think the primary issues with this machine will be rust related. It is ate up with rust. That is why I believe it will need a new cutter head. The entire cylinder and blades are inundated with rust. I was thinking of picking up a spiral head in case I do have to replace it. I would first see if the rust on the cutterhead is cosmetic, making sure the gaps that hold the bars/blades is flat, but if it's too far gone or looks/feels unsafe, yes I'd replace the cutterhead. I'd replace the blades either way. What Jay said was a good point; my thinking was that the outfeed table is likely already in the ballpark of where it needed to be adjusted and stayed put for too long and rusted to that spot. So a little adjustment of the knives up and down could do the trick. However, one thing to consider with the spiral is that you can't exactly do that with the knifes on those. Maybe shim underneath the bearing blocks, but even that might not do it. So it would be very important that outfeed table get restored. But if the issue is rust, I think with a little work and some 'careful' strength you can get that going again. Quote
Fricasseekid Posted October 18, 2012 Author Report Posted October 18, 2012 Good deal, I'll keep that in mind. The thought of shimming 32 or so teeth all to the perfect height doesn't at all sound appealing. Quote
slachammer Posted October 18, 2012 Report Posted October 18, 2012 http://www.deltamach...al-EnA06586.pdf wish i could find one for that price , good luck with it Quote
Fricasseekid Posted October 18, 2012 Author Report Posted October 18, 2012 Thanks, that should come in handy. Quote
Fricasseekid Posted October 29, 2012 Author Report Posted October 29, 2012 Thank you guys for all the advice! Here's the latest update: Everything on the machine moves freely. The rust will take loads of work to remove but doesn't hinder operation as far as I can tell. The blades even seem like they will be good to go with a good cleaning and sharpening. I'm pretty stoked! It seems I have gotten a steal @ $160 for something that could be worth about $700 by the time I clean her up. Unfortunately it's not old enough to be one of the models made in America, I don't know exactly what year it was made but it says made in Taiwan. So two hours and a half a bottle of WD40 here's what I got: The motor does seem in pretty poor shape. I hope it won't give me headaches down the road. Quote
Fricasseekid Posted October 29, 2012 Author Report Posted October 29, 2012 Maybe one of the Mods could change this thread title to "Kind of a love story." I say that because not only do I feel I have made a wise purchase, but I am excited about rebuilding this machine. I do not have much experience with jointers. I am very excited about getting know a tool that seems be of utmost importance in many a workshop. It's kind of an intimacy thing you know? You build a tool (or in my case rebuild) it becomes part of you and you can do incredible thing with it. It's like the love someone has for an old car they have cared for and brought back to a new glory. Anyone else experience this sort of thing before? Quote
TRBaker Posted October 29, 2012 Report Posted October 29, 2012 For a minute there, I thought you wanted it renamed "Kind of a love story", because you got screwed.LOLOLOL....Sorry, I couldn't help it. Looks like a deal. I would only caution you that the most important clean-up for you will be on the bed surface. Not only must the rust be removed, but the bed needs to be polished so that any wood you slide over it will move freely. If the surface is rough, it creates friction and drag as a result. It is not a safe situation to have to put super stength on a piece of wood while you are shoving it over three inches of open knives. The easier the wood pushes through, the safer for you. Quote
Fricasseekid Posted October 29, 2012 Author Report Posted October 29, 2012 Yeah, I'm still unsure about that part. I had actually considered removing the infeed and outfeed beds plus the back rail and taking them to a local machine shop to have them resurfaced. Overkill? With my table saw I just sand with 150 grit on the orbital, then spray the iron down with WD40 and let soak over night, then I wipe down and apply a generous coat of Johnson's paste wax. But I'm not sure if that is sufficient on a jointer since bed flatness is so critical. Any suggestions? Quote
STL Woodguy Posted October 29, 2012 Report Posted October 29, 2012 Resurfacing / scraping is doable, but I'd see what you can get out of the machine before going to that length. And based on what I've read on the topic (someone correct me if I'm wrong), you may have to bring the entire top half of the unit (no beds/tables removed) to get surfaced as the surfaces have to be flattened to one another. But what I will say is this: I wouldn't go 'too' overboard with getting an old jointer dead-dead-dead flat, you can easily drive yourself crazy doing so. I don't have a parallelogram jointer - otherwise I would have had a much easier time with the following - but I have a dovetail way jointer. So I basically went ballistic trying to shim each corner, throw feeler gauges underneath and finding something shifted. After too many hours, I threw the gauges aside, just used a Veritas straight edge alone and eyeballed it. And whadya know, after I ran a near 8" board through and checked it every which way, it was perfect and got it right on the first try. Haven't had to adjust it since. Regardless of what kind of jointer you have and what you need to do, if you run a board through and it's within tolerance of what you can work with, you're done. Quote
Fricasseekid Posted October 29, 2012 Author Report Posted October 29, 2012 It's funny you mention "within tolerance of what I can work with" because I almost never work with square lumber. I wouldnt know what thats like. I use a lot of reclaimed wood and find that with the right screw in the right place and enough wood clamps, wood can be very forgiving! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.