Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing cherry

Featured Replies

I'm building a shaker night stand from red cherry and need some advice for finishing it. I don't have much experience with furniture yet. I was thinking arm-r-seal satin to bring out the grain and protect it. Is that enough?

Do I need to coat with shellac first? Maybe sanding sealer?

I use a coat of Zinsser Bullseye Amber Shellac on all my cherry, it prevents blotching, and imparts a nice initial warm look. Then I arm-r-seal satin. Great natural looking finish that allows the cherry to age and darken naturally.

I use cherry fairly often and use home mixed, thinned boiled linseed oil & varnish. Wet sanding the wipe-on application up to 600-1200 grit depending on the mood. I've never used a base coat of sealer or shellac. To my eye the blotching is not a negative after a few months of aging. For commercial projects, perhaps it would be recommended. My suggestion is to consider using a shellac base, but don't assume that it is necessary just because you've heard folks recommending that path.

I believe that the shellac creates a seal, which can be a positive, but it also means that your subsequent finish will sit on top and not be sucked into the wood. Can't say that is a bad thing, but I like watching the effect of the oil/varnish going into the cherry.

Try variations and observe. Especially with cherry, the color deepening and richness development happens rather quickly. To my mind cherry is rather forgiving and beautiful. Enjoy.

Additional thought. Just noticed that you are creating a Shaker-inspired design. So I'll up my bet that any splotching will feel natural for Shaker furniture. Yep. Not sure how I'm qualified to speak for the Shaker comfort with splotching, but...

I build most of my projects using cherry. I always use Charles Neil's Conditioner for blotch control. It's water based and very easy to use. I've had excellent results using it. You can then use whatever you want for a finish.

Good luck!

Second on the Charles Neil conditioner. I used to use 1lb cut of shellac but find the Charles Neil stuff works better. Plus it can be sprayed (by me who doesn't have facilities to spray flammable stuff like shellac).

  • 2 weeks later...
  • Author

Do you recommend using blotch control even without stain?

I've tested the bottom of the top with straight arm-r-seal and like the look.

I'm nervous about the top looking splotchy and ruining the project

The thing about Cherry is that some boards will blotch and some will not. You can usually tell if you sand it to 180 or better and look at an angle. If you see a lot of grain direction changes noticeable by the difference in sheen, you will blotch. Even with conditioner you will get a little blotching in that situation. One way around that it to reject these boards during stock selection. You can get blotching even without stain due to uneven finish absorption. Wipe on some Naptha to get an idea what it will look like with finish -- if it will blotch, you will see it there.

For what it's worth, I've been doing an experiment recently with a scrap of cherry. I wiped on one coat of blonde shellac and put a drink coaster on it to block the sunlight and then set it outside in my yard in the full sun for two days. Since then (about two weeks), it's been sitting near a window; my wife keeps closing the blinds so I'm not sure how much sunlight hits it. I was surprised at how quickly it darkened in just two days. The color here (as it appears on my monitor) is very close to how it really looks.

This is what it looks like after that treatment:

8241773720_93444e5668.jpg

Cherry darkening experiment by gregwest98, on Flickr

==> it prevents blotching

how about "lowers the risk of blotching...." i spray 2 coats of #1ct SB if i want to "prevent" blotch, but even that sometimes fails. CN makes something he sell as "Blotch Control". Haven't tried it.

  • Author

I finished with the Zinsers unwaxed shellac, followed by Arm-r-seal satin. For some reason I have always been afraid to use shellac, but when I tested shellac under arn-r-seal on the bottom I couldn't believe the amount of depth it brought out of the grain. I only have one coat of arm-r-seal on so far. I'll post pics after the third coat dries.

Thanks for all of the advice and helping me discover how good a coat of shellac can look.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.