longahc Posted December 31, 2012 Report Posted December 31, 2012 Curious if this cut would be safe. What concerns me is the width of the board after the cut is 1/2" and would I be able to keep that balanced on the edge? Is there a safer way to make this cut? Saw is right tilt and I have the fence on the left side of the blade. Thanks for your suggestions. Aaron Quote
Boatworks Today Posted December 31, 2012 Report Posted December 31, 2012 Personally I hate making those types of cuts; I've grown rather fond of my hands and fingers . If it were me I think I would be tempted to do one of two things. 1) cut the majority of the material off with a bandsaw and then clean up on the TS making more or less a skim cut or 2) Same as above but clean up the cut on the jointer.. Not sure what tools you have at your disposal but I think you're in the right to be leery of this.. Good luck :-) Quote
chicks82 Posted December 31, 2012 Report Posted December 31, 2012 I make cuts like this often on my TS. But i do not use the stock throat plate. I have a zero clearance plate which gives the piece much more support. I also use a push block that keeps my hands far away from the blade. Along with the push block I stand to the side (which I personally do with just about every cut) so that if it does catch it does not come straight back at me. This is for sure not the safest cut by any means and if I had a band saw I would probably do what boat suggested. Quote
Eric. Posted December 31, 2012 Report Posted December 31, 2012 Yeah, those cuts suck, but that one doesn't look too too bad. I absolutely positively wouldn't do it with that stock insert you have there...at the very least you need a ZCI...and of course a good push stick. Edit: You beat me to it, Charles. Ditto what he said. Quote
longahc Posted January 1, 2013 Author Report Posted January 1, 2013 Thank you all. My bandsaw is about as useful as a kerosene heater in Death Valley for a cut like this due to drift. I remember this kind of cut on Woodsmith Shop and they were doing a much narrower width after the bevel was cut - but you're right - they did have a ZCI and skimmed it rather than doing it all at once. So I put in a ZCI to give better support and skimmed the cuts. I did notice an occasional rocking after I passed my Grip Tite - so if I do it again I will get another Grip Tite and put it after the blade. Quote
Nben Posted January 1, 2013 Report Posted January 1, 2013 It is generally a bad idea to put a feather board after the blade. Quote
tdale51@yahoo.com Posted January 1, 2013 Report Posted January 1, 2013 I agree with Nben. Generally it is a bad idea to put a feather board behind the blade because it causes the cut off to put pinching pressure against the blade. However I wonder if you could fashion some sort of upside down "L" shaped keeper to place behind the blade that only contacts the flat uncut portion of your stock. I think that would work if you just pushed the keeper up to just barely touch the stock with out applying too much pressure to tilt the piece and cause the bottom to come away from the fence. and please use a push stick. Quote
Alan Bienlein Posted January 1, 2013 Report Posted January 1, 2013 The feather board is in front of the blade before the piece gets cut. Remember this is a right tilt saw with the fence to the left of the blade and your looking at it from the out feed side. Quote
Eric. Posted January 1, 2013 Report Posted January 1, 2013 I think he's talking about putting a second featherboard behind the blade for doing a skim cut after the bulk of the material is removed on the initial pass. Which would be fine since there would be no off-cut material to bind into the blade. However, with the nature of that particular bevel cut, your featherboard would be pushing into the angle of that bevel, which would cause the piece to lift up instead of being forced against the fence. Quote
dwacker Posted January 1, 2013 Report Posted January 1, 2013 I would not skim cut it with what looks like a thin kerf blade in the photo. I'd just install a zero clearance insert and cut it in two passes. The first 90% through where its perfectly safe. The last pass is next to nothing with very little if any effort for the operator or saw. Don Quote
longahc Posted January 1, 2013 Author Report Posted January 1, 2013 Yes, featherboard after the blade WITH a cutoff is a bad idea. I was speaking of doing what Eric mentioned - using a featherboard after the blade but without an offcut. It was the skim cuts that were difficult to balance with a push stick and I heard the board tilt into the blade a couple of times. Judging from the marks on the board it was the top of the board leaning into the blade (as opposed to the bottom of the board tilting into the blade - which, if this board were any taller, an auxiliary fence would prevent). The Grip-Tite before the blade didn't lift up the board on the skim cuts - perhaps a function of that particular featherboard and/or my downward pressure with the push stick. I thought that the featherboard after the blade (without offcut) would give me the lateral pressure against the fence and all I'd have to worry about was downward pressure. Aaron Quote
Freddie Posted January 3, 2013 Report Posted January 3, 2013 When i had to make a bunch of raised panels for a cradle like this on the tablesaw, i made a tall aux fence that actually slipped snugly over my fence. I was able to clamp the work pieces to this fence and safely pass the panels through the blade with my hands far away. I quickly made it from scrap mdf amd discarded it after the panels were raised, but it was a life saver. Quote
Dave Posted January 3, 2013 Report Posted January 3, 2013 if possible i don't cut the board to width until last. Cut the bevel on a 4" or 6" board, then set the TS blade to 90deg and cut to width (your finished piece on the left of the blade) Use the extra width of the board to safely push thru the TS. Not sure if i explaned that very well. Quote
chipmaster Posted January 4, 2013 Report Posted January 4, 2013 I recently had the same cut, same issues. My solution was to push the work almost all the way through but stopped the blade when there was about three or four inches left to cut. I finished the cut with a hand saw and cleaned up the edge with my hand plane. There may be a better way but at the time I felt pretty good about it as I counted my didgits :-] Quote
Byrdie Posted January 7, 2013 Report Posted January 7, 2013 I'd fashion a jig that works like a tenon cutting jig - rides up against the fence and clamps your work piece to it. Then run that against the fence and over the blade. I'm not exactly sure what they're called but use the clamps like the ones that are on the Kreg pocket hole drilling jig. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.