Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Can I wipe on poly over stain?

Featured Replies

i feel like i should know this, and i would normally reference Marc's book, but i left it at the office.  so i have a project that i stained with some minwax cherry stain.  now i need to put a varnish on for protection.  can i use a wiping varnish lightly thinned with mineral spirits over the stain, or will it cause the stain to smear/run?  if necessary, i can get a spray on poly.  i don't have an HVLP, so i'd have to settle for something in a can.

Nick, if it were me, I would spray a light coat of the canned stuff first to just seal it off and then scuff coat sand it with 320. After that, you can wipe on all you want with no problems.

Okay just to be sure I understand all of the products you are talking about using are Poly... Right?

 

If so, then there is very little difference.
Brush on Poly is simply polyurethane. Polyurethane is more robust than either shellac, or even lacquer. Shellac, as you probably know, is naturally occuring, very similar to carnuba wax for your car. It is similarly harvested and similar in protective properties. Where as Polyurethane is man-made so to speak. Polyurethane differs from lacquer in that lacquer will disolve itself so that if your finished piece is damaged, you can reapply additional lacquer to the piece to repair it. Where as Polyurethane, is much more durable, but it does not disolve itself. So, once dried, if your piece is damaged, you have to sand off the old polyurethane to replace (not repair) it.

 

Now, assuming we are talking about polyurethane.


Brush on is fine over stain.

Wipe on polyurethane is EXACTLY the same as brush on polyurethane but thinned 50%.

Spray on polyurethane is 10% polyurethne and 90% propellant.

 

So, once your stain is completely dry and finished you can put any of the three on your piece and it won't matter. It is merely a question of drying time and thickness of the coat of poly.

Seal it...  TRB's idea is good, but dewaxed shellac (wipe or spray) is much faster.

+1

Got burned once with varnish lifting some stain on vertical surface that had dried 3 days. Now shellac goes between dye or stain and topcoats. Another benefit it gives is your topcoats will build faster.

You could try on a test block.

I just did a project where I had two coats of stain on cherry and when I went to wipe on the arm r seal it pulled some of the stain off enough that I had to let it dry Andy basically sand down and start over.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.