Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Installing lights flush to the ceiling

Featured Replies

Hi guys, I will soon be getting standard fluorescent lighting for my garage and i want to install them so that they are recessed into the ceiling. I would rather do this as i don't have a lot of head room and knowing me i will smash many a tube otherwise. Im thinking of 5ft 58W twin bulb units. Is it possible to do with standard fittings or will i have to get the stupidly expensive recessed fittings? More questions depending on the answer to this one :) Thanks

How high are your ceilings?

 

The 4 foot 4x32w T8 fixtures I put in my basement worked best screwed to the joists, as they throw a decent amount of light out the long sides.  The fixtures are only 3" thick, and don't seem to be a problem, even with my 7 1/2' ceiling.   They have plastic shrouds that provide some protection to the tubes. The wrap fixtures provide superior light distribution compared to my previous repurposed suspended ceiling fixtures and shop lights.

 

They're very similar to this:

http://www.lowes.com/ProductDisplay?partNumber=184346-13537-184346&langId=-1&storeId=10151&productId=1225811&catalogId=10051&cmRelshp=req&rel=nofollow&cId=PDIO1

 

If you recess them, you may gain a few inches, but you may also lose quite a bit of dispersion. 

also keep in mind if you recess you will have hard time in future to get the balast most of the lights i have fixed you have to open it from the top to work on those parts.  if it was me i would just hang em and get some tubes to put around the lights bulbs.

Is the ceiling sheeted or not either way it would be easy to do. If it is sheeted with dry wall mark out a square about 1" bigger than the fixture inbetween the ceiling joist bays use a drywall key hole saw and cut the square out build a 2x4 box the size of the opening screw a piece of OSB on the top of the 2x4 box, sneak this box through the hole in the drywall, and screw the box to the perimiter of the hole in the drywall, drill a hole in the top of the box for the wire to go through mount the light to the OSB with screws and wire it up ground to ground white to white black to black put the cover back on, and your in buissness. Now if it is unsheeted just screw a piece of OSB across the tops of your ceiling joists 1" longer than the length of your light drill a hole through the OSB for the wire, and you get the rest hope this helps.

If you want to recess them between the joists you could center them in the width and make 2 beveled white reflectors to help spread the light. You are going to end up with light and dark striped zones between the fixtures, due to the recess. I use cheap Ikea architects swing arm lamps and compact Flouresent flood light bulbs around my shop so I can direct extra light where I need it. I think they were about $10 each. The base can clamp or screw to a table or wall.

Fluorescent diffusers are specifically designed to spread the light from these fixtures and that is how so many commercial designs get away with setting these lights in an acoustical ceiling tile grid. You lose a moderate amount of intensity but should not suffer dark zones. There are higher intensity fixtures and I would strongly encourage the investment. As for a light that requires top service for ballast replacement, I have never seen such an application after having serviced many thousands of fixtures. I would have to say they are an oddity.

  • Author

Thanks all. I havent boarded out the rafters yet so for now i will just screw them to the rafters and at least i can use them. If i need to move them i can do it later as long as i tell the sparky to leave me enough cable :)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.