Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Price v Quality Expectation (Rockler HVLP)

Featured Replies

Ok. All the guys I know, that have the systems, use a gun with the cup on the top.

Most systems come with a pressure feed siphon. Better ones like Apollo use a kremlin gun that can go either way. Fuji may also go either way not sure. But these are not in the same league as Earlex or one like the op is looking at. I can't even buy a needle set for $120.

I have actually used the unit in question. It works. But it doesn't offer much control and it is made with cheap parts that can break fairly easily. For the occasional sprayer, it could actually get the job done. But if you are using lots of different finishes requiring fine tuning for good atomization or if you spray a lot, I'd look toward Earlex as a starting point or better yet, something like the Fuji MiniMite.

If you are going to spray every other month get this system. If you are going to spray every week or less get a better system.

I've never seen an HVLP gun with a siphon cup.

They are very popular. Gravity guns are what your "guy" are seeing. They are also HVLP. I personally don't like them.

I also own the exact unit in question, but I paid about $60 for it 10 years ago at Harbor Freight.   I still use it for outdoor stains and preservatives. 

 

The main con is the inability to adjust the tip size to match viscosity.  This means the finish must be thinned to a narrow range.  With finishes like NC lacquer, shellac, dyes, and pigment stains, it's not an issue.  With complex formula finishes, like water based stuff, it's nearly impossible.  It's also impossible to get spare parts.  If it breaks, it's a door stop.  It's also a bleeder gun, so air blows when you release the trigger.  It's lots of fun blowing crap into your wet finish...

 

I also have a Fuji 4 stage, complete with 4 needle setups, top and bottom feed guns, teflon lined cups, and a 2 quart pressure pot.  When I bought the Fuji, Earlex didn't exist.  The only choices were the cheapie HF unit, and $800-$1000+ Fuji, Apollo, etc...  pro-level turbines.   

 

Some of the Earlex systems look terrific for lower volume stuff, and Earlex seems to offer spare parts, as well as support on Internet forums.   For my purposes, some of the better Earlex units could have saved me some money.

 

No matter what system you get, consider a 120v dust collector remote (if you don't already have one) to turn the turbine on and off.  I like to do this between boards, as the air stays cooler.   On hot days, adding more hose helps, I use a 50' black rubber garden hose, but having an easy way to cycle the turbine can really help.

==> No matter what system you get, consider a 120v dust collector remote (if you don't already have one) to turn the turbine on and off.  I like to do this between boards, as the air stays cooler. 

 

I've been tempted to try this, but worried that the cooling would form condensate -- so, once on, I tend to leave it on and just use a long host to manage heat...

==> No matter what system you get, consider a 120v dust collector remote (if you don't already have one) to turn the turbine on and off.  I like to do this between boards, as the air stays cooler. 

 

I've been tempted to try this, but worried that the cooling would form condensate -- so, once on, I tend to leave it on and just use a long host to manage heat...

 

 

It has not been a problem for me, and some of the WB is pretty fussy stuff.  It never really cools down.  It usually goes a few minutes on, a few minutes off, repeated as necessary.  The turbine stays in a slightly warm state.

 

Interesting thought, though...  I'll keep it in mind if I get an issue. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.