Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Uncle asked me to restore his grandfathers chair

Featured Replies

Ok so my uncle requested that I restore his grandfathers (my great grandfathers) chair. He wants to keep the finish as is but just about all of the glue has failed. There are also cracks that need to be repaired and one of the cross members needs to be either to be returned or repaired some how. My thought is to get a heat gun to help me loosen any of the glue that is still intact and take the piece apart and put it back together with our newer PVA glues, most likely TBII. Here is a link to pictures of the chair and it's problem areas https://www.dropbox.com/sh/znb4pyc46f1mjkx/XCZEbzP74k

 

My question is what would you guys do?

Definitely a unique and interesting piece and going to be worth the effort.  Some creative clamping and careful insertion of glue should help close up those cracks in the seat.  The botched repair of the stretcher, however, is going to be a challenge.  You'll have to remove the broken stump and the screw repair from the leg.  You'll also have to somehow replace the missing wood on the end of the stretcher.  Perhaps doweling on a piece and then turning it to size and shape or using a draw knife or spokeshave.

 

Chairs like that aren't common and it's definitely worth conserving.

just go to ikea....................:)

 

Is that a crack or just the board separating?  that would make it easer to fix.  to get glue in the crack put it on the top and use a vacuum to pull it down into the crack. its too thin for a business card pusher to shove the glue down into the crack.  you might need to turn a new cross stretcher for the chair but you might be able to reshape and clean it up with careful carving. 

 

as for the finish are you sure that finish and not just  years of dirt and sweat?

Charles,

 

I love that chair  :wub: . The patina is awesome and also the design is a new one on me. For me on image 2 I would not even attempt to try and re-glue unless it's falling apart.

 

Again Image 3, I would be tempted to leave well alone unless the joint is moving or getting worse quickly. I would not expect glue and a clamp would do much on Image 3 as the split is not full length.

 

Image four does require some work. I would cut the stump back to a shoulder line in the turning. I would then turn/have someone else turn a new stump with a projecting pin to join into the cut off stretcher. You could then drill a hole in the end of the stretcher and glue the stump in. I would assume the stretcher would be fox wedged in to the old hole.

 

Duck +1 on the finish and it will be really tricky to match, that's why for me less more, accept some of the splits and I really really like that chair.

  • Author

Image Two is the boards separated and my grandfather fixed it by screwing a 1x4 to the bottom to secure it. So i will be pulling that off and gluing that. In image 3 the crack shown is much longer on the back. It almost goes to the top my thought was to maybe use some thin CA and a syringe then clamp. I like you suggestion on the stretch GS. As far as the rest of the joints most are very lose and the glue has failed so i could take apart and re-glue or use CA and a syringe to stiffen it all.

Scarf joint the stretcher you dont need a lathe just a rasp and bandsaw. If your going to take it apart the back can be glue injected with a screw through the arm joint, you will never know its there. The seat I would remove the current repair inject glue, clamp and add a small dutchman.

CH,

 

As you point out if the two boards are loose they will need a look. You could add some serrated dowels to aid location and a bit of extra strength to the joint. Just really try and avoid removing any of that patina from the visible faces

 

PB also gives a viable second option on the stretcher too.

Cool chair. I'd suggest using hide glue for the repairs, someone else may need to do more work in a couple of generations.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.