Recommended Posts

Posted

Now that I have my first wood project made since Jr. Highschool, over 30 years ago (the blender base posted in showcase) I thought it was time to do something a little bigger.

This shelving unit is in a book on bookcases. It was designed to be knocked down and the shelves were positioned with biscuits. I am just using this as a starting point. I am going to install the shelves with blind dado and tenon joinery in place of the biscuits. I am also going to take the bottom shelve section and install a back and a front door, hinged at the bottom to be a clothes hamper VS the shelve section that is in the plans.

 

I purchased Black Walnut to make this unit but when talking to a wood working buddy, he thought that the unit might be a little rickety or have excessive movement not be rock solid as it is without a back. So, instead of using $250+ of black walnut to start, I am making a trial unit out of red oak, about $75 in material.

 

The walnut is in wide enough sections to make the 13.5 inch sides and shelves but the oak was in 9 inch at the most, wide boards so I had to join two boards to make each side.

 

This is the first time I have tried anything like this and so far I think it is working out OK. I used my 6 inch jointer on the 8 foot long boards. I bought some supports to hold either end of the boards both into and out of the jointer and I am using MagSwitches to hold the stock square into the jointer. On the inboard side, just a feather board but on the out side of the jointer, I used the resaw fence from MagSwitch, there is a single roller in the center and a tapered inlet and exit to the fence so any slight misalignment is corrected as I pass by it, it holds the stock firmly against the jointers fence.

 

This is a pic of the page in the book showing my starting point. For copyright reasons, I will not show the cut list with dimensions (just to be safe) but the bottom is 13.5 deep, and 18.5 inside dim, wide. The top is 9.5 deep and 12.5 wide.The unit tapers on a 3 deg angle both from bottom to top and 3 deg on each side to the middle.

 

 

post-14128-0-40050200-1374504357_thumb.j

Posted

The following pictures are of the glue up and plaining flat of one side of the unit. The first side, I did not use cardboard shims between the metal supports clamped to the glue up to keep it flat and the tight bond 2 stuck so well to a block of alum, that it tore out some grain. On the second board, I fixed this by using cardboard between the metal and the wood so that I would not have that issue again.

 

I did a dry fit out of the jointer, then installed biscuits for alignment and did another dry fit. I had everything ready for the glue up then did the glue.

 

I used my No 8 jointer to flatten the glue up by going side to side, 45 deg and along the grain. Then I used my No. 4 smoother to, well smooth it out. I still have a few spots of grain issues and I will either sand or use a scraper to clean it up.

 

I used blue tape to make an outline of the side I need to cut out on the first side I did, there is still a little mineral spirits drying from the board. I wiped it down so I could see if there were any glue spots that my interfere with finishing later. The end of the board is wide and long enough to do the bottom shelves, saving glue up of these later.

post-14128-0-76791500-1374504966_thumb.j

post-14128-0-69929000-1374504990_thumb.j

post-14128-0-14093900-1374505022_thumb.j

post-14128-0-94139800-1374505063_thumb.j

Posted

More pics. In the tape outline pic, the OUTSIDE of the tape, is the cut line of the side. To get a better way to see and align the sides for cutout, I am going to make a full size cutout in some cardboard, that way, I can move the cutout around to get the best match from each glue up. This is all I was able to do over the weekend, I will try to get more done soon but we all know how "life" gets in the way of making plans :D

post-14128-0-72280800-1374505185_thumb.j

post-14128-0-22099700-1374505220_thumb.j

post-14128-0-95787500-1374505240_thumb.j

post-14128-0-58858100-1374505266_thumb.j

post-14128-0-27706200-1374505308_thumb.j

post-14128-0-15988000-1374505338_thumb.j

post-14128-0-59479800-1374505358_thumb.j

post-14128-0-33522000-1374505397_thumb.j

post-14128-0-05097000-1374505427_thumb.j

Posted

Cal, I would think twice about using your Black Walnut in 13.5" width, all one piece. A board that wide tends to cup easily and you might be better off gluing up several narrower widths.  By the way, you're doing an outstanding job on the oak unit. You might like it so well that you decide to use the walnut for something else. :)

Posted

Troy,

Thank you for the kind words, I was hoping for some feed back on how I am doing.

The point you make about the Black Walnut is a good one, it just shows how much of a noob I am when it comes to wood! I completely forgot about movement, well I did not think it would be much anyway.

 

I was going to use the Black Walnut as the rest of the bathroom is a dark finish wood (no clue what it is) and my personal feeling about stain/coloring wood is that .... if you want a wood to look like XXX then USE XXX LOL! I spent as much time picking out the Black Walnut as I did the Red Oak (see below) and I would hate to cut it up into thinner boards then glue back together and loose the great grain pattern that is in the wider boards. I'm not sure what to do now.

 

I spent a long time pawing through the large stack of red oak at the lumber yard. It was in the bargain area at $2.35 a board foot. It took a lot of digging to get a reasonable color match and similar grain patterns along the edges. I moved so much wood around that the check out woman, asked if I had "found what I needed OK" with a knowing smile, not smart A$$ but knowing! (she was only about 15 feet away the whole time helping other customers) It was S2SSL1E 4/4 but as it was S2S, finish size was 3/4. I have not measured what thickness remains after planing flat the joined boards but I doubt it was more than 1/8" removed total for both sides. I will just go by inside dims and all should be OK. A slight bit thinner won't bother me in the least.

Posted

I don't think it will be too "rickety" because of the shape. Think of it like a parallelogram.

Since you have a trapezoidal shape, it will still be able to move. I am not 100% on the geometry, as I am just picturing it in my head, but I think the movement would be somewhat more restricted as compared to a normal rectangular shelving unit.

If it really concerns you, glue in some triangles under the bottom of the bottom shelf in the corners to help add strength. You could even do this on all the shelves for continuity if it looks good.

Nice progress, by the way.

Posted

Cal,

 

First of I like the project, the bookcase looks really nice in the book/photo. The tusk style wedged tenon adds something unique to a very simple design. Your progress looks good too, tight and tidy. TRB is right on the risk of movement but to hell with that, gamble  :). The pain of seeing wide stock reduced to smaller sections is too much to bear.

Posted

I would put a back lip on the shelves to keep things from falling off and that would stiffen up the whole structure as well. I think 3/4" above the shelf should be plenty.

Posted

Thank you to everyone, great comments and things to think about.

I went out last night to start to square the long sides of my glueups I have an inexpensive straight edge and I should have known better.

 

I am OK as it was just a very minimum cleanup cut and I have a lot of width to play with but the guide flexed in the center and I wound up with about a 1/4" inward bow down the eight foot side. I am now on the lookout for a solid straight edge and it looks like I will need to pony up a little cash for it. I am looking at the Bora 100" clamp. I like the swivel pads on the clamps, I need to cut several 3 deg angles and to a noob, it sounds like a useful feature.

 

I know if I had a straight piece of stock I could trust to be dead straight, I could clamp it down to layout lines to make it work. I know I am a bit of a tool nerd though. As I don't have much to remove on this one board to true it up, I was going to go with a router over the circ saw I used last time. I think I will have less side pressure on whatever straight edge I am using. I just wanted a good flat side to start layout from, ahh well I will keep muddling along.

 

I might even continue to make the second unit from the Black Walnut, it sure is pretty wood. I hope to get more done this weekend, I only get weekends for the most part as my daily job takes a LOT of my time.

Posted

I know it is Wed but this is what I got done last weekend. I cut both cab sides to finish size. I first cut one side then cut the other side about 1/16 oversize then flush routed the second to the first.

 

I also laid out and cut the blank for the router temp to be used to cut all 4 mortise through cuts for the shelves on top and bottom. The new DRO on the table saw worked perfectly, I set it to the desired cut and it was bang on.

Also being used for more than just a square cut was my Kraig micro adjust protractor head. As the sides of the case measured to 3 1/2 deg, I set the same angle on the head and the desired width of my long side 5 5/16 on the stop and it was also perfect the first time through.

 

I then checked the router temp blank angle to the cut angle on one of the cab sides by lining up both cut sides to compliment each other so the edges should be the same on top and bottom edges, they were!

 

I am happy with the "match" of two sides of the case, four boards to equal two sides. Now I need to finish the router temp and cut the through cuts, then the shelves and so on. Much left to do but it is progress.

 

I did buy the Bora clamp on straight edges, they work fantastic, I highly advise to buy them if you need a good straight edge. They held firmly and at an angle with no deflection while using a circular saw to cut the wood.

 

 

post-14128-0-90114900-1375301961_thumb.j

post-14128-0-73186400-1375301982_thumb.j

post-14128-0-58075400-1375302007_thumb.j

post-14128-0-18373300-1375302033_thumb.j

post-14128-0-95633600-1375302061_thumb.j

post-14128-0-33542500-1375302099_thumb.j

post-14128-0-53331800-1375302120_thumb.j

Posted

This is checking the match of the router temp.

 

I am very happy with how accurate it came out. The old PM66 may be battle worn, rode hard and put away wet before I got her as is evident in her looks but she is still a very solid and accurate table saw!

 

post-14128-0-31154500-1375302356_thumb.j

post-14128-0-74758100-1375302445_thumb.j

post-14128-0-89696000-1375302508_thumb.j

post-14128-0-30460100-1375302570_thumb.j

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 39 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined