Recommended Posts

Posted

FT is being very circumspect -- They won't comment on exactly what the safety issue is, what the fix is and/or when the fix will be available.

 

Here is what I've heard, but it may or may not be the actual recall issue -- the question has been put directly to FT, but they won't comment...

 

For the 'R', the saw's internal DC was redesigned.  If you run the saw without proper airflow, sawdust accumulates in the riving knife mechanism.  During a plunge, the knife will extend, but not retract after the cut.  The mechanism jams.  The implication is that the riving knife mechanism fails unless you use a high-quality vac attached to the saw... Ie, they didn't test the saw with other mfg's vac systems or run it without vac at all (bet someone looses his xMas bonus over that one).

 

The issue has been widely reported, but FT won't comment on the riving knife issue at all -- or even if this the issue behind the recall.  If you ever looked under the hood at the guts of a 55/75/R/etc, then you'd see the fix may require a redesign of the saw body.  The 'R' has been available in Europe for quite a while -- so we're talking about an expensive and time consuming fix...  The fact that the govt's involved means that FT has to prove root cause and successful remediation -- all that takes time.  I bet into '14.

 

I've got an 'R' now and happily using it...  but i'm also keeping my eye on the riving knife...

Posted

I was finally ready to make the jump into the world of Festool by picking up the TS 55REQ with the money I made off of my first commission, and of course it was the day after the recall. I'm keeping my fingers crossed that they end the recall before 2014, because that money is burning a hole in my pocket! I guess if I push comes to shove, I could always use the 1400 router.  Why does life have to be full of tough decisions? :rolleyes: 

Posted

I was finally ready to make the jump into the world of Festool by picking up the TS 55REQ with the money I made off of my first commission, and of course it was the day after the recall. I'm keeping my fingers crossed that they end the recall before 2014, because that money is burning a hole in my pocket! I guess if I push comes to shove, I could always use the 1400 router.  Why does life have to be full of tough decisions? :rolleyes: 

 

I have the both.  The track saw is a game-changer.  Better to wait.  Or pick-up a used TS 55 (without the "R").

 

 

miw

Posted

Thanks Missioninwood.  I was wondering if I should just go ahead and pick up the TS55 or just wait until the REQ comes back out.  Which, I think would be like asking to make a root canal to last as long as possible.  Is the difference between the TS55 and TS55REQ that big that I would be kicking myself for not waiting?  

Posted

==> Is the difference between the TS55 and TS55REQ that big that I would be kicking myself for not waiting?  

 

FT has a video on their site highlighting the differences.  What they might mean for you depends on your projects.  I think FT's reconditioned-tool sale is still going-on, so you may pick-up a 55 for a few less $$.   

Posted

The differences are slight.  The body was modified to get up closer to walls for flooring work and the depth setting now has micro adjustability.  The other "improvements" are marketing gimmicks, I suspect.

 

I ripped 1 1/2" thick white oak with the thing a few weels ago.  Fantastic tool.  :D

 

 

miw

Posted

As said here there is no word on when the 55 will be available but the reconditioned tool sale is still going till the end of august so if you want one goto your festool dealer or festoolusa.com and see if there are some available.

Posted

jmack,

 

    What you going to use it for 90% of the time? The TS 75 might not be a bad purchase. If you know you are going to be cutting thicker material all day with it, or doing anything with metal the TS 75 is the way to go. Otherwise if you are just doing sheet good break down then get a TS55.

Posted

Charles,  I'd be using it for breaking down sheet goods most of the time.  As for lumber, most of the time it's just 4/4 stuff, with the occasional 8/4 piece added in for flavor.  

 

However, it looks like I'm going to have to wait a little while longer.  My cell phone just took a nasty fall today, and is done for.  So the "Festool Fund" is going to be turning into the "Mack's new phone fund".  <_<   Oh well, I'll just have to crank out a few more jobs before I can pick one up.  I guess it'll make me appreciate it more when I do finally get one.  

Posted

Charles,  I'd be using it for breaking down sheet goods most of the time.  As for lumber, most of the time it's just 4/4 stuff, with the occasional 8/4 piece added in for flavor.  

 

However, it looks like I'm going to have to wait a little while longer.  My cell phone just took a nasty fall today, and is done for.  So the "Festool Fund" is going to be turning into the "Mack's new phone fund".  <_<   Oh well, I'll just have to crank out a few more jobs before I can pick one up.  I guess it'll make me appreciate it more when I do finally get one.  

 

Sorry to hear about the phone. I keep my phone in an OtterBox all the time. I don't care how pretty Apple believes there phone to be, 'cause you can't see it  :-)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 56 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined