Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Thinning Arm-R-Seal!?

Featured Replies

In another post, I talked about a big mistake I made building doors for a wall hanging cabinet. Since then, I fix the doors which look really good, but I am having a little bit of trouble getting a nice finish that doesn's looked streaky. I am using Arm-R-Seal and am wondering if thinning would be a good idea? I looked at the back of the can and it says to not thin. It also says that you could use mineral spirits to clean up. I am assuming the can says not to thin only for EPA purposes. And if I do thin, do I use mineral spirits, and what mixture would work best?

How are you applying it?

 

I've never had an issue with it streaking but, I've only wiped it on.

  • Author

ugh. Honestly a little of both. When I originally made the doors I wiped it on. And they looked "ok". When I repaired the doors I had a brilliant idea to try and spray it with pretty bad results. I have sprayed lacquer many times in the past and am actually pretty good spraying, but for whatever reason I left a rough surface. I sanded the roughness down before posting. I just want a better finish than I had wiping, and I am wondering if thinning it would do the trick.

Spraying with what?   Is it a bit too viscous for the tip in your sprayer?

 

I've never tried to spray it to be honest.

  • Author

I have never tried spraying it myself either. I just have a snap-on spray gun with a 1.5mm tip. A 50 gallon compressor also. I don't know why I tried spraying it, just had the urge. I have no problem going back to wiping it on, being that it is sanded back down and small.

  • Author

Streaky is probably not the right way to describe the look when I wiped it on. I am using a gloss, and some areas look like they are absorbing a lot more finish and leaving more of a satin to semi gloss appearance.

When wiping, the key is not to spread it too thin (which is easy to do while wiping).  Thin coats are what results in streaking.  Best thing is to really load up your rag (I typically place a bunch of cotton balls in the middle of a towel and twist everything into a loose ball) then make my swipes.  Maybe one or two passes per area and don't get too concerned about even-ness; it flows out.. 

 

I've never sprayed it, but guessing that the same thing is happening..  By the time the solvent evaporates (which would be spirits), the resulting film is a little on the thin side to give a proper appearance.  

 

Finishes that are meant for wiping typically don't do well spraying (they result in runs, sags, etc); and vice-verse, but with dry spray and orange peel..

 

Not sure if this makes sense :unsure: ...

  • Author

Boatworks, that makes perfect sense. I was trying to use thin coats because I know Arm-R-Seal is a urethane and wanted to stay away polyurethane plastic look. So thinning is a bad idea I take it?

Arm-R-Seal  is already thinned quite a bit out of the can (which is what allows it to be a wiping finish).  I've never had a need for further mixing.  It can be applied somewhat thick and you still don't get a 'plastic' look.  It's good stuff; I've really come to like it for personal projects  :). 

Streaky is probably not the right way to describe the look when I wiped it on. I am using a gloss, and some areas look like they are absorbing a lot more finish and leaving more of a satin to semi gloss appearance.

You mean its an uneven sheen? Did you stir that can?

  • Author

I just put a thick coat on, when it dries I will try and post pictures if I am still having the same problem. Its pretty hard for me to describe. 

 

TKF, I shake. not stir. I hope that isn't causing my problems. 

I just put a thick coat on, when it dries I will try and post pictures if I am still having the same problem. Its pretty hard for me to describe. 

 

TKF, I shake. not stir. I hope that isn't causing my problems. 

Stirring is recommended. Shaken causes bubbles which means you'll now need to strain your finish before spraying. You aren't James Bond now are you?

  • Author

LOL I think I realized my problem. Before the mistake I made on the doors, I finished the cabinet. The finish on the cabinet turned out really nice! I finished the cabinet in a climate control basement which is probably somewhere around 70 degrees. I have been trying to finish the doors in the garage, which is about 85 degrees. I checked the finish and it looked bad AGAIN, even with a thicker coat. I sanded it back down a layer or two, and when I went to apply the finish again. I realized it was tacking up within less than 2 minutes. The places that were getting sticky faster than the rest ended up being the areas that didn't look right. So I moved them back into the basement and am hoping to have this thing done tomorrow! 

Keep a wet edge, just like painting a wall. Get the Arm-R-Seal on and don't over work it. If you want a thinner product use General Finishes Seal-A-Cell. Arm-R-Seal is a thicker product that has higher solids for faster build. Oh yeah and now you know about the heat thing. Yep cooler room temp the better. :)

 

-Ace-

  • Author

Well I didn't have much luck with the Arm-R-Seal. I think I may have had an old can or something. No matter what I did, I couldn't get the finish to look right. I have used it in the past with a lot better luck.

 

I ended up giving up and decided to run to Home Depot to buy a plain can of Poly. Thinned the poly like I have done plenty of times in the past, sprayed it on, and it looks really good. Heck, even the wife is satisfied with it. I put a final coat on the inside of the doors, and hope to have pictures of it hanging in the bathroom tomorrow!

WOW!  Definitely something weird there.

  • Author

What happens to finish when it gets old, or sits out in the air to long? I usually buy small pints and almost always use the majority of it up on the project I am working on. The reason I ask is because I remember thinking to myself that the can wasn't as full as I thought it should have been. I am wondering if someone previously bought it, and returned it to the store.

 

.....OR I just don't know how to properly wipe on a finish  :unsure:

...  and hope to have pictures of it hanging in the bathroom tomorrow!

 

English is such a wonderful language!  I hang pictures of all my projects in the bathroom too!  :o

  • 2 weeks later...

Streaky is probably not the right way to describe the look when I wiped it on. I am using a gloss, and some areas look like they are absorbing a lot more finish and leaving more of a satin to semi gloss appearance.

Hey Pat, I use Arm-R-Seal a lot and when that happens its because I did not use a sealer or something to prevent blotching. What I end up doing is to sand between coats and keep applying coats till it goes away, sometimes 6 or 7 coats. I don't believe thinning will do much more besides make you need more coats. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.