Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Joinery Bench Build Featuring the BenchCrafted Moxon Vise

Featured Replies

This build is also featured on my blog if you want to check it out here.

Some Notes On the Build:

There will be an article in the first issue of Weekend Warrior Woodworking Magazine on this joinery bench but I thought it would be fun to document the build on the blog also. This bench is going to serve two purposes. The first purpose is what a joinery bench is intended for and that’s well…joinery! The second is to significantly reduce my excess lumber. I have some white oak that has been sitting in my shop for a couple of years along with some tiger maple that I started to use in a desk project. I was not happy with how the desk build was going so I scraped it. Individually these species are not enough for the bench by themselves but together they will form the bench top, apron and tool well. The only problem is that all this material is 4/4, so that means a lot of lamination! For those of you looking for a drawing, plan and cut list right out of the gate, I am sorry to say that I just don’t have one right now. However, in the magazine I will put in a cut list and more of a plan. Right now I am going with the no plan plan. I am just not sure how everything is going to come together at this point and still working out some of the details. I am thinking that instead of dovetails for the apron I may opt for pinned rabbets. I think they are easier and will be just a strong.

I know I said I was not going to use a lot of hand tools but it was late at night and this was honestly the easiest way for me to break down the rough white oak. I crosscut each board to roughly 36″ using a Disston cross cut saw. This was a rough length and a good amount over the final dimension. I am aiming for a final width of about 32″ with 28″ between the screws and about 20″-22″ deep.

DSC01296-150x150.jpgDSC012981-150x150.jpg

 

 

 

 

 

 

After I crosscut all the white oak to roughly 36″, I needed to rip the white oak and tiger maple to rough width. For ripping I turned to my Festool TS75 and guide rail set on top of styrofoam insulation. I like the TS75 because I can set the guide rail to rip the edge of the board that is unusable and there is no way for me to put it on the jointer. I can also angle the guide rail to taper the rip cut and save most of the board and only rip the unusable edges of the rough board. When the rip is completed I have nice clean straight edge on each board. I am not saying this is the best way, this is just my preferred method of ripping rough stock. One could easily use a circular saw with a straight edge, bandsaw, jigsaw or go for the cardio work out and use a rip saw!

DSC013911-150x150.jpgDSC013931-150x150.jpg

 

 

 

 

The tiger maple was pre-milled already because a majority of it was taken right from t he desk project I started to scrap and just need to crosscut it close to final dimension. For the cross cuts I used theFestool TS75 and MFT/3. Cross cutting on the MFT/3 is one of my favorite methods of cross cutting. I don’t own miter saw but I don’t feel like I need one with the TS75 and MFT/3. I trip one end of edge board clean, mark a line for 36″ set up flip stop and make a cut. I then am able to crosscut multiple boards at once, I just use my finger to feel if the ends of the freshly cross-cut portions are lined up. This is not final length so it does not need to be perfect just close.

DSC014051-150x150.jpgDSC014091-150x150.jpgDSC01408-150x150.jpg

 

 

 

 

 

I next wanted to rip each of the rough white oak boards the a width of around 3.25″, I could have used the TS75 for this, I would have just had to put a support board underneath the guide rail but opted for the bandsaw instead. I had a clean straight edge on each board already, so I just put the clean edge up against the bandsaw fence and ripped the pieces of white oak to width. I am not saying that my methods to dimension stock are the best, just what I prefer to use in my and shop and what seems to work for me.

DSC01436-150x150.jpgDSC01438-150x150.jpg

 

 

 

 

 

 

When I took these pictures the bandsaw was off!

Next up, laminating the tiger maple boards and milling the white oak! Thanks again for reading, if you any questions for comments please feel free to email me or better yet post them in the comment section for everyone else to see and learn.

remind me later and ill show you a picture of my bench.  I designed it more for carving and still changing it every few days.

Nice one James, I look forward to the progress. On dovetailing the apron, FWIW, do it! I'm with you on it not being essential, that said it would look good and be nice and strong.

  • Author

Nice one James, I look forward to the progress. On dovetailing the apron, FWIW, do it! I'm with you on it not being essential, that said it would look good and be nice and strong.

Thanks Graham! You may end up talking me into dovetails but the I like the pinned rabbet option, which I believe is still very strong. I think its a more viable option for someone who did not want to cut dovetails or who may be intimidated by dovetails. 

  • Author

Thanks Graham, I am sure you are right, thank you for the link! Instructables is a pretty good website. I have actually cut dovetails before, now granted I am not the best "dovetailer" but I have cut some. I like to do things a little different sometimes and the pinned rabbet option makes the joinery bench a little more approachable. 

  • 2 weeks later...
  • Author

Joinery Bench Build: Lamination, Lamination Lamination!

Like the title stated this last part of the build involved a lot of lamination! The entire bench top is made out laminated 3/4″ material, the bench is about 16″ wide. This meant that there where about 20 individual boards that need to be laminated together to get the 16″ width I was looking for. The best way to tackle this lamination process was in several stages. I wanted to make sure that each initial section was less than 6″ wide, this way I could run them across the jointer and planer after the first glue up. I wanted to try to stack the cards in my favor as much as possible in order to end up with as close to flat surface as I possibly could. Click here to check out the pictures on my blog. 

James, the bench looks great.

I'm not the best "dovetailer" either, but I suggest using them as they look great when completed and besides that the practice really helps.

Just my two cents.

  • Author

Well, I may just have to suck it up and cut the dovetails!

  • 2 weeks later...
  • Author

I have made some good progress on the joinery bench in fact it’s almost done but I am little behind on my posts. I have been taking a crap load of pictures and it takes awhile to sort through them all. I know I did not make a Try Square in September but believe me when I say that I did get some good practice in. I will have to admit that I was little nervous to flatten the top of the bench, as my hand planing skills still need work. I tried the best I could during the lamination process to make the top as flat as possible but despite my best efforts it still needed to be flattened by hand.

I decided the “warm-up” by flattening the bottom first, this would give my some practice before flattening the top. I felt pretty comfortable after flattening the bottom, so I went straight into flattening the top. It took me about an hour after and after it was all said and done I had a flat top. It’s significantly more satisfying than you would think to flatten a top like this buy hand!

I then took the top over the jointer and jointed one edge straight. The top, because of its size was a little awkward  to run across the jointer but it worked out fine. I then took the top over to the Festool MFT/3 and cut it to length. After it was cut to length, I took it over the table saw and cut the top to final width. I then marked and cut the tenon’s using the MFT/3 and TS 75. I made a short video here, showing the process. Visit Weekend Warrior Woodworking Blog to see more pictures. 

post-104-0-13700000-1381394787_thumb.jpg

  • Author

mmmmmm shavings. Good progress James and good on you for flattening with a hand plane.

Thanks Graham but you will be disappointed when I tell you that I did not use dovetails for the apron! 

  • Author

For the Joinery Bench aprons, I went with 8/4 hard maple. I started by cutting the boards to rough length before milling. This makes it easier for me to handle to 8/4 material on my 6” jointer. You can read the entire post here, with a lot more details and pictures on the apron.

post-104-0-49592800-1382031372_thumb.jpg

  • Author

Joinery Bench: Installing the Moxon Vise and Finishing Up!

The Moxon Vise installation is complete and the joinery bench is ready for use. Actually I finished it last week and have been using it for the last week or so. Here are some pictures and more details on the bench and hardware installation. There will be an article in the first issue of Weekend Warrior Woodworking Magazine on the joinery bench. You can check out more details and pictures on blog post here. 

post-104-0-40898000-1382549121_thumb.jpg

Thanks Graham but you will be disappointed when I tell you that I did not use dovetails for the apron! 

 

No way dude, whatever works right?  :) The finished article looks great btw.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.