Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Rubbing out a water based finish

Featured Replies

Typically, I use solvent finishes. After the finish has cured for a week or so, I typically use 0000 steel wool and paste wax to "finish the finish", as Marc says.

I have recently switched over to spraying water Bourne finishes. Any tips on rubbing out a water based finish? Some people have posted that steel wool should never be used with a water Bourne finish due to rusting issues, but I can't see how it would rust if the finish is cured and used after the final coat. Perhaps they are referring to between coats.

I have also read that some people use mineral oil and wet dry sandpaper, while others use mineral spirits and wet/dry paper.

Any advice for a newbie to water based finishing?

  • Author

Just wet dry and water is fine so is steel wool after cured.

What grit do you normally use?

What grit do you normally use?

I don't it's not necessary for anything I do. :) It really depends on how bad of a spray job you did 600 or 800 wet is a good starting point for a bad spray job and go all the way up to 2000 then polish.

  • Author

I don't it's not necessary for anything I do. :) It really depends on how bad of a spray job you did 600 or 800 wet is a good starting point for a bad spray job and go all the way up to 2000 then polish.

I am quite happy with spray results I achieved. I just feel like I "should" rub it out.

==> mineral oil and wet dry sandpaper, while others use mineral spirits and wet/dry paper

 

The whole steel wool, rottenstone, pumise, et al is passing into the sunset since products like Abralon and automotive glazes have made their way into woodworking...

 

Charles Niel just published a video on his revised "finish the finish" schedule... Basically flatten-out using 400/600WD w/soapy water and take it to matte, then work your way through Abralon 1000-4000 and finish with a glaze...

 

I just completed a birdseye glove table and decided to give CN's schedule a go and compare the results against my 'old school' schedule....  It works incredibly well and far less messy...

I use a red, grey and white non woven abrasive pad like Scotch Brite to rub out my waterborne finishes. You can also use a clean brown paper bag as a final buff. Sometimes it is wise to let the finish cure a few days before doing any serious rubbing out.

==> let the finish cure a few days before doing any serious rubbing out. 

 

that's an excellent point -- I usually let it cure for about a week...  I think Flexner has a table for rub-out wait times...  I believe it goes-out something like three weeks for some...

  • 4 months later...
  • Author

==> mineral oil and wet dry sandpaper, while others use mineral spirits and wet/dry paper

 

The whole steel wool, rottenstone, pumise, et al is passing into the sunset since products like Abralon and automotive glazes have made their way into woodworking...

 

Charles Niel just published a video on his revised "finish the finish" schedule... Basically flatten-out using 400/600WD w/soapy water and take it to matte, then work your way through Abralon 1000-4000 and finish with a glaze...

 

I just completed a birdseye glove table and decided to give CN's schedule a go and compare the results against my 'old school' schedule....  It works incredibly well and far less messy...

Can you post a link to the video? I went looking today and couldn't locate it.

  • Author

Thanks, but I have seen that video before. I thought there was an updated version.

==>I thought there was an updated version. 

There is... Let me poke around around some...

 

CN pushed some paid content onto his free site (similar to what Marc does on occasion)... I bet that's where it is...

Triple H got it right,,, How can I help ?   The new video is in an on line class I do ..Sorry, but will be happy to answer

 

BTW , a 10 day cure period will do fine for about any waterbase finish.

Triple H got it right,,, How can I help ?   The new video is in an on line class I do ..Sorry, but will be happy to answer

 

BTW , a 10 day cure period will do fine for about any waterbase finish.

 

Do you have a formula to calculate curing time on force cured WB.

No I dont , you need to check with the finish manufacture , they all have different times ..

 

All I can get is the standard answer 120f max 5-15 minutes dwell dry but not full cure or the typical 7 day full ambient cure. The only one I can get a real answer from is ML Campbell but there are no dealers around here. Using their times/temps just blisters the hell out of General and target both. Am I wrong in assuming these can be force cured like catalyzed lacquer?

Typically, I use solvent finishes. After the finish has cured for a week or so, I typically use 0000 steel wool and paste wax to "finish the finish", as Marc says.

I have recently switched over to spraying water Bourne finishes. Any tips on rubbing out a water based finish? Some people have posted that steel wool should never be used with a water Bourne finish due to rusting issues, but I can't see how it would rust if the finish is cured and used after the final coat. Perhaps they are referring to between coats.

I have also read that some people use mineral oil and wet dry sandpaper, while others use mineral spirits and wet/dry paper.

Any advice for a newbie to water based finishing?

 

I do the dish soap and water and Alabron pad's. Some finishes like Target, I recall say not to use a lubricant. Just sanding dry and use a pad. Target was having some issues at the time. I have had no issues with the soap and water on General Finishes topcoats. As Charles Neil said, just make sure the finish has ample time to dry/cure and it shouldn't be a problem.

 

-Ace-

  • Author

Triple H got it right,,, How can I help ?   The new video is in an on line class I do ..Sorry, but will be happy to answer

 

BTW , a 10 day cure period will do fine for about any waterbase finish.

I am looking for the "best" way to rub out a water borne topcoat. I use genral finishes high performance poly and endurovar most often. I spray with an earlex spray station, and I like the results. Currently I am using paste wax and 0000 steel wool to rub out my finish, but I hear if other guys using different methods. I was wondering what you feel is the best method.

And thanks for all your great videos, I have watched many hours of your material on youtube and your website,

  • Popular Post

My issue with steel wool is it doesn't leave a clear crisp sheel, but more of a muted one, I do not like the scratches it leaves, while waxing helps, it still shows .

 

My preference is to use the Abralon pads , a 1000 will give you a matt sheen, 2000 a low end of a satin a 3000 is a high satin/semi gloss  ( depending on how much you rub) and 4000 is a gloss. I use a little soapy water as a lubricant, just be sure not to let the white slurry dry on the surface or it can be a bear to get off, Keep it clean . THe other thing with any rubbed surface is it will appear hazy/cloudy .. its just the nature of the beast .. You can go to your local autobidy supply and tell them you want some "swirl remover", it will remove the haze. Its basically like a wax , but not a wax and no silicones, its designed for a new finish . Works well. If you get too much sheen , simply drop a grit and go over it again, The abralon only comes in 6" pads , and can be washed out and reused .

 

 If you have debris, you want to use a silicon carbide sand paper ( black, waterproof)  in about a 600 to 1200 grit, depending on severity of the debris, the finer the paper the better . ( less to rub). You want to use a block and sand the debris flat, because the Abralon pads are a sponge pad and will ride over the debris, and while it will smooth it, it will no level it.

 

As a swirl remover, fina;l "waxing" this is one of my favorites http://www.calcarcover.com/product.aspx?cid=110&id=1399 , I have also seen it in some auto stores  like Pep Boys and Advance Auto .

 

 Woodcraft sells the Abralon pads, and some have told me thsy found them on Ebay , also here is a link to a guy who sells tham as well as the SIA Aire   www.bowlingbeat.com

 

hope this helps

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.