bobcrosley Posted October 7, 2013 Report Posted October 7, 2013 I'm currently looking for a good deal on a used 6" jointer. Since we rent right now, and I don't (and can't) have 220 in the garage, I need to stick with a 6". So the goal is to find a good deal on a decent 6" that I will be able to sell when we move somewhere I can get an 8" jointer. I have found a good price on an older Delta. It was certainly not their bargain basement model. But it's about a 30 minute drive away. Looking at the pictures, there's a little surface rust on the fence, but there's some nastier looking stuff at the very end of the outfeed table. The seller is selling it for his grandfather and is not a 'tool guy,' so he can't really tell me if the rust is pitting the cast iron or not. So before I drive out there, I'm wondering if some pitting at the very end (limited to the last 4-5") of the outfeed table is a deal killer? I know the jointer is a tool that's often set up to tolerances in the thousands of an inch, but I also know that the infeed table and the first part of the outfeed table are most critical for precision. What do you think? Worth the drive to take a look? Or should I stay away? Quote
TerryMcK Posted October 7, 2013 Report Posted October 7, 2013 If I were you I would drive over Bob and take a look. It may just be superficial and even if it is pitted it may still be ok. Take a straight edge as a twisted table is far worse. Quote
Freddie Posted October 7, 2013 Report Posted October 7, 2013 Bob i believe you can get a delta dj20 which is an 8" and can be wired to 110 or 220. I would look for one used to keep cost down and you wont have to buy a jointer twice. Quote
dwacker Posted October 7, 2013 Report Posted October 7, 2013 I would not buy a 6" If your stuck with 110v you can get the Delta but it may be hard to find. Personally Id buy and 8" + and just swap out the motor. If you keep in mind while your using it that it has a smaller moter you will not have any issues. Most use a 3450rpm 3hp motor its cheap and easy to find a 3450 rpm 1.5-2 hp. But no a little pitting is not an issue as long as the table are in good shape otherwise. 1 Quote
Freddie Posted October 8, 2013 Report Posted October 8, 2013 http://nwct.craigslist.org/tls/4096622873.html One showed up in my area on cl, they do exist! Quote
tim0625 Posted October 11, 2013 Report Posted October 11, 2013 Some surface rust and even some pitting would not be an issue for me. Clean it up and wax it. I'm with Terry...take a straight edge and maybe a little steel wool and brush the rust off and check it out. Quote
Trip Posted October 11, 2013 Report Posted October 11, 2013 ==> I would not buy a 6" If your stuck with 110v you can get the Delta but it may be hard to find. Personally Id buy and 8" + and just swap out the motor. If you keep in mind while ==> your using it that it has a smaller moter you will not have any issues. Most use a 3450rpm 3hp motor its cheap and easy to find a 3450 rpm 1.5-2 hp. ==> But no a little pitting is not an issue as long as the table are in good shape otherwise. +1 Quote
wdwerker Posted October 11, 2013 Report Posted October 11, 2013 You could fill the pitting if the rest of the table is flat. If it is warped or twisted its junk. Quote
Freddie Posted October 11, 2013 Report Posted October 11, 2013 I think we should be focusing on the delta dj-20 better off buying it now than buying a 6" now and an 8" in a couple of years. If you buy a 6" now with pits then you might struggle selling it in a few years. Something to consider if you plan on upgrading down the line. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.