Recommended Posts

Posted

I have posted on here several times about the challenges I have had getting my table saw setup.  It is a Delta Tilting arbor saw, technically a hybrid saw.  There is not enough play in the bolt holes to get the motor/blade aligned to the mitre slots.  I am guessing this is why the previous owner added the sliding table for cross cuts.  Check out the picture.

 

I seems like I am constantly having to mess with the crosscut fence to get the thing to cut square and even then it is erratic.  

 

The sliding table is solid and there is no play in it at all.  I got to thinking last night that I had to remove the sliding table assembly previously and maybe it is out of alignment front to back.  I have not checked this yet.

 

A different table saw is the future, but for now I need to make this thing work.  Any suggestions?  Since the mitre slots can't be aligned to the blade without modification to the saw, the sliding table is the only way I have to make cross cuts.  

 

I have considered trying to make a crosscut sled that has the fence setup to compensate for the mitre slot being out of alignment, but seems like I should be able to get the sliding table aligned with blade so I have not done that yet.  I am also not sure if a crosscut sled would work or be safe, so any input on that would be appreciated as well

 

This thing is becoming a real pain in my *$@.  It seems like every time I need to make crosscuts I spend an hour trying to get it aligned and even then my results are not great.  

 

Josh

post-14301-0-94712100-1388666970_thumb.j

Posted

==> There is not enough play in the bolt holes to get the motor/blade aligned to the mitre slots

Forgive me if this is stating the obvious, but the way you worded the issue has me a bit confused...

 

You align the miter slots to the blade, not the other way around...

 

I've owned 3 cabinet saws and all had over-sized/elongated mounting holes for adjusting the top/slots to the blade. If not, the holes are typically enlarged with a reamer...

Posted

http://woodgears.ca/delta_saw/alignment.html

This guy also had some difficulty but it seems the difficulty was just actually shifting the pieces and not too little travel. I would almost wonder if top or trunions were not original and were replaced at some point. If you get adventurous, try this guy's process. Tip your saw over and remove the cabinet and post some closeup pics of your trouble.

Posted

I hate to sound like the lazy type, but I'd just buy the new saw.  Sometimes a tool can become more trouble than it's worth.  Put that thing on Craigslist and make it some other guy's problem.

Posted

Eric, I know what you mean but if you cannot guarantee a perfect setup before you purchase then you will have to do your final fit on your new saw also. The hope is for a one time fitting with occasional renewal. It seems like Josh, you have never dialed in that first fitting. If it is doable you should only need to fit it once with minor tweaks annually or so. Then again, I enjoy the metal work almost as much as the woodwork.

Posted

==> There is not enough play in the bolt holes to get the motor/blade aligned to the mitre slots

Forgive me if this is stating the obvious, but the way you worded the issue has me a bit confused...

 

You align the miter slots to the blade, not the other way around...

 

I've owned 3 cabinet saws and all had over-sized/elongated mounting holes for adjusting the top/slots to the blade. If not, the holes are typically enlarged with a reamer...

Its not a cabinet saw though, so the whole motor, trunnions, and blade have to move rather than the top.  Wish it was that easy.  

 

 

I hate to sound like the lazy type, but I'd just buy the new saw.  Sometimes a tool can become more trouble than it's worth.  Put that thing on Craigslist and make it some other guy's problem.

 

I am just about there, but need to save a bit more money first.  

 

 

I have tried numerous times to get the mitre slot aligned to the blade, with no luck.  On the last go around I finally realized there was just not enough play in the holes.  My only option would be to take the whole thing apart and make the holes larger.  Since I planned to get a new saw, I was hoping to just make the sliding table work for now, and simply not use the mitre slots.  

Posted

http://woodgears.ca/delta_saw/alignment.html

This guy also had some difficulty but it seems the difficulty was just actually shifting the pieces and not too little travel. I would almost wonder if top or trunions were not original and were replaced at some point. If you get adventurous, try this guy's process. Tip your saw over and remove the cabinet and post some closeup pics of your trouble.

 

 

This is what I need to do to fix fix the mitre slot alignment issue. Thanks for the link.  

Posted

To answer the original question about building a cross cut sled to solve the problem, it wouldn't work if the slots are not parallel to the blade.  Even though the back fence on the sled may be perpendicular to the blade, the direction of the slot would push the cut toward or away from the blade.  Same effect as a rip fence that is out of alignment to the blade.  You would either end up with a cut that binds or pulls away from blade and the possibility of kickback is a reality.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined