mds2 Posted January 7, 2014 Report Posted January 7, 2014 I need a jointer. Need. For three years I've been face and edge jointing by hand. Good skills to have, but I need to be more efficient. Originally I thought a 6" would be ok, but the last time I bought lumber every board was over 7" wide. So I think and 8" would be ideal. My biggest problem though is power. I have 15 amp circuits to my garage with 14-2 wiring. My panel is maxed out. I've added space saver breakers everywhere I could. (As a side, whoever puts only 100amp panels in house should have their builders license revoked.) Are there 8" jointers available that I can use? Quote
dwacker Posted January 7, 2014 Report Posted January 7, 2014 Check the specs on the delta. Last time you bought wood everything was over 7" wide? But how wide was it at use? Quote
mds2 Posted January 7, 2014 Author Report Posted January 7, 2014 Finished piece sizes were around 6" max. I'd like to be able to joint before doing any rips if I can eliminate that step. Plus I'd like to not have to upgrade in a year. Pretty much everything I've read recommends getting an 8" instead of a 6" if possible. I'll look into the delta, but aren't they now defunct? or on the way to being defunct? Quote
dwacker Posted January 7, 2014 Report Posted January 7, 2014 Finished piece sizes were around 6" max. I'd like to be able to joint before doing any rips if I can eliminate that step. Plus I'd like to not have to upgrade in a year. Pretty much everything I've read recommends getting an 8" instead of a 6" if possible. I'll look into the delta, but aren't they now defunct? or on the way to being defunct? The only 8" I know of that runs on 110 is the delta. Everything else is going to need at least a 20a 220. The idea of jointing in a single pass then going to the saw and ripping into smaller pieces is not a good one. Quote
mds2 Posted January 7, 2014 Author Report Posted January 7, 2014 Why is that? Especially If I don't have a jointed edge I'd have to rip them on the bandsaw. I prefer to keep the wide boards wide if I can. Quote
Tom King Posted January 7, 2014 Report Posted January 7, 2014 Take a couple of the already used spaces in your panel, and feed a sub-panel. You can put the two circuits that were taking that space in the new panel. If you can't do it, it's a pretty simple job for an electrician. You can buy everything you need at Lowes or Home Depot. Then you can run a 240 motor on the jointer. 1 Quote
pghmyn Posted January 7, 2014 Report Posted January 7, 2014 I'm not sure if PB is referring to this, but this is something that has happened to me. I was cutting up a 7" wide board into 3x 2" pieces for a project. I jointed one side and ripped the pieces about a 1/16" heavy in case of movement. I underestimated the movement, and had to do some fiddling with my project to accommodate the smaller size I had to rip to. If you are ripping smaller pieces from a wider piece, plan for movement. If you can get the pieces to a manageable width close to your final dimensions, and then joint them, it might save some future headaches. Quote
dwacker Posted January 7, 2014 Report Posted January 7, 2014 Why is that? Especially If I don't have a jointed edge I'd have to rip them on the bandsaw. I prefer to keep the wide boards wide if I can. You dont want to pre machine your wood. For example. You dont joint and plane a 7" board to rip into 2 3" boards. Rip your 7" board into two 3 1/2 boards joint and plane then rip to your final 3". It may seem like more work but you are going to relieve your wide board and end up with two unusable narrow boards because they bowed off the saw. Its just the facts of life in todays day of speed kiln drying lumber. Quote
Trip Posted January 7, 2014 Report Posted January 7, 2014 ==>100amp panels in house ==>My panel is maxed out. ==>I've added space saver breakers everywhere I could. ==>Take a couple of the already used spaces in your panel, and feed a sub-panel. Your service disconnect is 100a? I'm assuming most of your major appliances are gas? I believe NEC 2011.230 permits 100a service, but I believe you're supposed to have 2 free lugs (someone should chime-in on this)... That 'maxed-out' and 'space-saver' breakers sound like you've got no room to grow, much less add woodworking machines... Since your looking at stationary tools, rather than under-powering your jointer (which may piss-you-off two years from now) and/or spending the $ to run a sub, I'd seriously consider a service upgrade. If your service cable is already 200a (probably), can reuse your breakers (most likely), got some slack in the branch lines (maybe), then it might not be that big a $$ deal... Before plunking-down $$ on a jointer that you may out-grow, I'd ask an electrician to take a look and at least give you a ballpark -- shouldn't cost you anything but time... Anyway, my 2c. Quote
Guest Posted January 7, 2014 Report Posted January 7, 2014 You dont want to pre machine your wood. For example. You dont joint and plane a 7" board to rip into 2 3" boards. Rip your 7" board into two 3 1/2 boards joint and plane then rip to your final 3". It may seem like more work but you are going to relieve your wide board and end up with two unusable narrow boards because they bowed off the saw. Its just the facts of life in todays day of speed kiln drying lumber. You can also maximize your yield that way. When you are face jointing a board, you need to remove everything from between the highest spot and the lowest spot to make it flat. If you rip the board in half, you now have two boards, each of which will likely have less deviation between their respective high and low spots. It might be impossible to get a 4/4 7" wide board perfectly flat without taking it all the way down to 5/8" thick or even less. But rip it in half and you will likely be able to get it done. FWIW, I have a 6" jointer and have never felt the need for an 8" jointer. Yes there are times I'd like to face joint a wider board, but in those cases 8" wouldn't get it done either. I'd need a 12" jointer to be perfectly happy. If you need to flatten a wide board there are all kinds of things you can do with a combination of hand planes, a 6" jointer, and a planer to get it done. I know everyone says a 6" jointer is too small, they are probably right but an 8" model doesn't necessarily solve that problem. I got the best 6" model I could afford (which cost more than many 8" models) but a jointer is a precision tool so flat, long beds with easy set up were more important to me. Quote
pghmyn Posted January 7, 2014 Report Posted January 7, 2014 ==>100amp panels in house ==>My panel is maxed out. ==>I've added space saver breakers everywhere I could. ==>Take a couple of the already used spaces in your panel, and feed a sub-panel. Your service disconnect is 100a? I'm assuming most of your major appliances are gas? I believe NEC 2011.230 permits 100a service, but I believe you're supposed to have 2 free lugs (someone should chime-in on this)... That 'maxed-out' and 'space-saver' breakers sound like you've got no room to grow, much less add woodworking machines... Since your looking at stationary tools, rather than under-powering your jointer (which may piss-you-off two years from now) and/or spending the $ to run a sub, I'd seriously consider a service upgrade. If your service cable is already 200a (probably), can reuse your breakers (most likely), got some slack in the branch lines (maybe), then it might not be that big a $$ deal... Before plunking-down $$ on a jointer that you may out-grow, I'd ask an electrician to take a look and at least give you a ballpark -- shouldn't cost you anything but time... Anyway, my 2c. If you can get a free estimate, this might be the best option just to see where you stand. Quote
mds2 Posted January 7, 2014 Author Report Posted January 7, 2014 Upgrading electrical is a heavy consideration of mine. Running a sub panel to the garage has been something I've wanted to do since I've bought the house. Long ago I had a friend of mine, who is a lineman for the city electric, looked at it and said I only had 100 amps coming to the house. Everything here is underground and he told me it would be ridiculously expensive to have a new cable pulled. That severely limited what I wanted to do. This is actually the reason why I got into woodworking. Before this hobby I was starting to get into welding and metalworking. I enjoyed it a lot, but couldn't do it at home. My dads shop is over an hour away each way. There is/was no way to run a decent welder at my place. So I switched to this. Anyway, this recent summer my neighbor put a small addition on and he had also thought we only 100 amp service to the house, but turns out we have 200. So this spring I'll take the above advise and get a free estimate from a licensed electrical contractor. The electrical has been a bottle neck long enough! Its also limiting my desk collector options quite a bit. Now as far as jointers/jointing: I thinking more along the lines of ripping a 6" board out of a 7" piece, why handle it twice? But I understand about ripping 3" boards out of a 6~" piece. The thing you guys say make perfect sense. I'm not against a 6", I just didn't want to buy something and immediately regret it. I think I'll look at those options a bit more. Quote
pghmyn Posted January 7, 2014 Report Posted January 7, 2014 Upgrading electrical is a heavy consideration of mine. Running a sub panel to the garage has been something I've wanted to do since I've bought the house. Long ago I had a friend of mine, who is a lineman for the city electric, looked at it and said I only had 100 amps coming to the house. Everything here is underground and he told me it would be ridiculously expensive to have a new cable pulled. That severely limited what I wanted to do. This is actually the reason why I got into woodworking. Before this hobby I was starting to get into welding and metalworking. I enjoyed it a lot, but couldn't do it at home. My dads shop is over an hour away each way. There is/was no way to run a decent welder at my place. So I switched to this. Anyway, this recent summer my neighbor put a small addition on and he had also thought we only 100 amp service to the house, but turns out we have 200. So this spring I'll take the above advise and get a free estimate from a licensed electrical contractor. The electrical has been a bottle neck long enough! Its also limiting my desk collector options quite a bit. Now as far as jointers/jointing: I thinking more along the lines of ripping a 6" board out of a 7" piece, why handle it twice? But I understand about ripping 3" boards out of a 6~" piece. The thing you guys say make perfect sense. I'm not against a 6", I just didn't want to buy something and immediately regret it. I think I'll look at those options a bit more. In your case, you would probably be okay with jointing the 7" and ripping to 6" wide. If there is any stress relieving, you will see it more noticeably in the 1" cut off. However, you might still see some in your 6" piece. You said you prepped stock by hand for 3 years. If there is a slight amount of deformation, you can probably get it out in one light pass with a plane. But, you will have the jointer, so you can just go back there, too. -EDIT- I wasn't against a 6" jointer when I was shopping, either. Although, I know that a lot of my stock was in that sweet spot of 7-9" wide -- so I opted for the 8" jointer. With the #4 Stanley I bought now, I can joint a 9-10" board flat enough to run through the planer in no time at all. The 8" bed is huge, and really a nice luxury to have for a small basement shop. Quote
Trip Posted January 7, 2014 Report Posted January 7, 2014 ==>he told me it would be ridiculously expensive to have a new cable pulled I've lived in several homes over the years and each and every time I've done a service upgrade, the utility pulled the new service cable for free (once for 750ft underground conduit) -- as long as it was tied to an upgrade order... I've now done this in two states and one province --- three different electric utilities -- all the same result... Never hurts to ask... A local electrician should know if you can work the system... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.