Recommended Posts

Posted

Hey folks, first time posting here.  I have a Stanley #8 and I'm having a difficult time edge jointing longer boards and keeping them at 90 degrees.  I've seen the Veritas jointer fence for their planes and the stanley 386 (?) fence.  The veritas only works on their jointer plane, and I'd rather not have to buy a vintage stanley fence and hope it works ok.  

 

I'm hoping I could just use a really hard piece of flat wood that i could screw or attach to the side of my plane.  Has anybody got experience doing this?  I'd rather not use clamps since its awkward.  Can I go about drilling and tapping two holes on the side of the plane so i could screw a piece of wood to it?  Is this advisable?  If so, would I need any specialized tools?  I dont know anything about working metal.

Posted

Hey folks, first time posting here.  I have a Stanley #8 and I'm having a difficult time edge jointing longer boards and keeping them at 90 degrees.  I've seen the Veritas jointer fence for their planes and the stanley 386 (?) fence.  The veritas only works on their jointer plane, and I'd rather not have to buy a vintage stanley fence and hope it works ok.  

 

I'm hoping I could just use a really hard piece of flat wood that i could screw or attach to the side of my plane.  Has anybody got experience doing this?  I'd rather not use clamps since its awkward.  Can I go about drilling and tapping two holes on the side of the plane so i could screw a piece of wood to it?  Is this advisable?  If so, would I need any specialized tools?  I dont know anything about working metal.

You sure about Veritas?  They used to sell one that attached with rare-Earth magnets and would work on practically any plane.

Posted

The veritas has magnets to fit other makers planes, and set screws to dial in 90 degrees or if you want another angle. You could probably make ur own and epoxy in a few rare earth magnets.

Posted

Yep, two different ones.  I have the one for their jointer.  I actually found I did better without it after a little practice - especially when I learned the right grip.

 

Indeed. I've never used one, but a little practice and you won't need one ever.

Posted

I have the fence with the magnets.  The magnets are plenty strong.  Its not like a table saw fence where you push a large board across.  Really it just requires fingertip pressure to keep the fence against the board.  There is a pin on the top that rests against the high shoulder on the side of the plane to prevent it from sliding back, and this also does a little to prevent rotating the fence and not the plane.

 

But I think the most important thing to remember when you are squaring the edge of a board with a hand plane (regardless of with or without the fence), is that the hand normally on the knob (front), is actually on the side of the plane in both cases acting as a fence with your thumb hooked on the top to help keep the plane in the cut.

 

I don't use the fence as often, as my wrist seems to have found 90*, but it does make a great set of training wheels.

 

you can also do what Chris Schwarz calls the dirty cheater method (which he he freely admits to using).  Basically its like shooting the long edge of the board.  Find some thin board 1/4-1/2" or whatever, and place the board to be planed on top of that with the edge to be worked facing away from you.  Clamp it down with holdfasts/clamps, spare people, and then put your plane on its side on the benchtop, blade towards you (now your bench acts as a giant fence), and take a couple passes to lock in 90*...(this works best if you already have the edge straight, and can't quite get it square)

Posted

I am sure the fence will help, but I encourage you to keep practicing at making a square edge.  Part of getting it square is fine tuning of the lateral adjustment as you go, which you will still need to do even with the fence. 

Posted

One other thing you may want to try is doubling up the boards that you edge join.

A little thicker edge sometimes helps make it easier to hit 90 degrees.

I hope I'm saying this right, easier to show than to type it :)

If you double boards up for a glue up (like for a table top), lay the boards flat like they will be when glued up, then get them together with the underneath of the top facing together on the inside, then joint the boards.

Try to joint the boards 90* but if you're off a little it won't really matter.

Posted

Thanks for the tips fellas.  I'll keep practicing I guess.  I think my body position is partly to blame.  I always take a heavier cut on the side closest to my body.  It just sucks when one end is leaning one way and the other end is leaning the opposite.  I feel like i take so many passes to fix the issue, but then mess up another part of the board then try to fix that and before I know it, ive taken like half an inch off.  :)  thinner shavings and constant checking with a square I guess.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.