wrenchguy Posted January 20, 2014 Report Posted January 20, 2014 Hey Guys and gals My first post on hear and wanted to share my Powermatic 66 That was just GAVE TO ME 1981 single phase motor Had to got to my basement but it was already disassembled, man these are heavy Its replacing my old chraftsman ive had a long time, so im excited I have it all put back in one piece and runs great.. BUT I think I want to upgrade the fence to a Beisemeyer style fence!!! I see a lot of these have the Accufence on them as well What do you think I should do???? Quote
Tom King Posted January 20, 2014 Report Posted January 20, 2014 That fence is actually not that bad. I have the same fence on one that I bought new in 1974, and it has been used since. Tune it up, add some sort of faces to it, keep silicone spray on the rails, and it works just fine. I like having the two levers where you lock the front one first, and then the back one. It actually makes a stronger fence than the Biesmeyer, which I also have one of, and the knob for fine adjustments is better than none on the Biesmeyer-plus that fence stays square while you move it while the Bies doesn't always because the fence is not as tightly guided by the front rail until you lock it down. In short, I wouldn't spend the money on changing it-just tune it. The main problem is the faces probably aren't square to the table since it's just heavy sheet metal folded over it, but you can fiddle with mounting new faces with through bolts, and spacers inside, and once you get it right, it will serve fine for decades. Quote
Rick LoDico Posted January 20, 2014 Report Posted January 20, 2014 I've got the Accufence on my PM66 and it's a great fence but I like the looks of the one that you have there. I wouldn't be in a rush to replace it. Quote
atlinwi202 Posted January 21, 2014 Report Posted January 21, 2014 You are lucky. That is a nice saw. Quote
wrenchguy Posted January 21, 2014 Author Report Posted January 21, 2014 Well every body says this fence is a good fence BUT!!! I had it off the saw tonight looking at it, the fence has 1 lobe on the inside when you lock down the lower handle it get tight like its suppose to. But it does not evenly square the fence each time!! I am a Ford technician so looking at mechanical things are common for me, but I don't see what would make the fence square each time its locked down!!! What am I missing??? Quote
knotscott Posted January 21, 2014 Report Posted January 21, 2014 Great saw! I'd much prefer a Biese style or Vega fence.....PM Accufence, Xacta II, HTC, Shop Fox Classic, Vega, etc.... Quote
Tom King Posted January 21, 2014 Report Posted January 21, 2014 Take the cover off the fence. At the front, there are two bolts. You can loosen them, and adjust the fence for square, Once you have it square, lock down the back to hold it, check, and retighten those two bolts. Once it's adjusted correctly, it can not only be locked down and stay square at any time, but it stays square as you move it. The Biesmeyer doesn't do that. The Bies has to be against the front rail to stay square. It can move back away from the front rail when the locking lever is released. When I first put the Biesmeyer on the Unisaw, it was a bit aggravating having to tap it to make small adjustments, that would be made with the knob on the Powermatic fence. I almost finally got used to it, but it still aggravates me sometimes. I changed the fence on the old Unisaw because the Delta fence was only good for scrap metal. I can't believe that anyone who has properly tuned, and used one of these fences actually prefers anything else. I don't think I've had to adjust the Powermatic fence since I did it the first time, and that was a LONG time ago. The scale on the Biesmeyer is nice, but I can actually set the Powermatic rail fence accurately, more quickly with a tape measure from the blade to the fence, simply because the Biesmeyer is not held tightly to the front rail when not tensioned with the lever, and can flop around behind the rail while trying to make a very small change. The fine adjustment knob pulls in and out too. Push it in to engage the rack to use. Pull it out to disengage the rack for big changes in cutting width quickly. Don't use silicone spray on the back rail-only the front rail. There is also an adjustment at the back for tension with that lock, but that one is obvious. Since the person you got the saw from didn't know how to adjust the fence, or maybe was too heavy handed with it, it's probably a safe bet that the blade is not precision aligned with the slots too. Cabinet saws are easy to get the blade aligned perfectly. There is a bolt under each corner of the top so you can only move the top, and not have to fiddle with all the mechanism underneath like you do with a small saw. Get it all aligned, and you will have a great saw to use. The only thing that worries me about your saw is the switch that someone added. Quote
wrenchguy Posted January 21, 2014 Author Report Posted January 21, 2014 Thanks Tom Ill look at it more tonight!!! Quote
wrenchguy Posted January 22, 2014 Author Report Posted January 22, 2014 Hey Tom you're the MAN!!!!! Got home today took the fence apart cleaned it up and found the 2 set screws that used to align the fence was loose!!!! So squared it all up!!! I cut 3 different size pieces and I used my MIC that I brought home from work and every size was less than .003 !!!! wow it works great now You just saved me about 400.00 bucks LOL Quote
Tom King Posted January 22, 2014 Report Posted January 22, 2014 Do you have a right wing for it, or do you need to make one? Quote
wrenchguy Posted January 22, 2014 Author Report Posted January 22, 2014 Yea Tom Im thinking about adding a extension that way and Put a router in there!! Any ideas on that and I want to add a folding outfeed table aswell. Quote
Tom King Posted January 26, 2014 Report Posted January 26, 2014 All you need is an angle iron or aluminum to bolt to the holes on the top on that side, and screws into a plywood top covered with Formica if you wish. That and an outfeed table are required to get the most out of a cabinet saw. I used 3/4 Birch from Lowes for mine with angles under for keeping it flat. That fence requires a gap at the back between the saw and the outfeed table because of the rear fence lock, but it doesn't hurt performance at all. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.