Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Aging Poplar

Featured Replies

I recently built a small folding table out of poplar. It has green streaks in it that, of course, will go away with time. I know that oxalic acid will eliminate the wait but I would rather let time do the deed.

 

I put a stain and a few coats of poly on a test piece and it made the green pop out even more. I want to use it in the mean time. I don’t mind the green so long as it goes away after a few months to a year. I don't know if I could wait longer than a few months though. I have it basking in the sun while I make this decision.

 

The question is, am I prolonging the aging process by sealing the poplar? Should I just suck it up and use the acid wash? Or skip the toxins and watch it gradually change to brown.

Where did you hear that the green streaks will "go away with time?"  That'd be a new one on me.

Green streaks will go brown. Non green streaks will go less brown. My caveat is that I am talking less than one hundred years. The streaks will still be streaks for a long, long time albeit less green. My dad poly-ed his poplar trim and it went brown, but not in a few months. In fact, I have not seen unfinished go brown in a few months. If you put it in direct sun you are more likely to get sun faded gray than brown.

Yeah I know they fade from green/purple to brown, but that's a far cry from "go away."  :)

There's a bunch of species termed "poplar" from two separate families -- some have green streaks, some brown, some none... Note: most of the lumber sold as 'poplar' is not from the Populus family, but from the Tulip Popular family (forget the Latin name)... The Tulip Poplars are the ones with more pronounced 'streaks' (pronounced heart/sap).

 

Depending on the species, the 'green streaks' will turn to brown over a couple of years... Also depending on the species, they may further fade and the sap darken. In a few species, the sap & heart kind of blur together into a uniform 'light brown'...

 

I made some shop furniture from 'poplar' (species unknown) about a decade ago. Today, it looks a bit like soft maple tinted with 'medium brown' Transtint.

  • Author

Thank you everyone! I am ok with the darker brown next to lighter brown, heart/sap/streaks. All blemishes and shades are welcome in my book except for green. Knowing that finishing the poplar with stain and poly won't stop the aging process is a relief. I can make my decision from here. I knew there were varying species but assumed they all aged to similar shades of brown. 

All the poplar I have worked with stayed green/brown/purple, what have you. I have boards in my shop over 5 years old still green. ;) What you have to do with poplar is to use a good alcohol or water based dye. You need to tone the heart and sapwood to give a foundation of color for your stain.

 

-Ace-

 

can check out my photo gallery on a lowboy I built from poplar.

Dye on the opposite site of the color wheel before your dark stain will all but make the streaks dissapear. If your going with a dark stain and your poplar has a bunch of green a red dye will hide the streaks.

There's a piece of poplar in my office that started quite green.  With a coat of shellac, it was a comfortable brown within half a year.  If I were you, I'd hold off on the the dyes and wait it out.

There's a piece of poplar in my office that started quite green.  With a coat of shellac, it was a comfortable brown within half a year.  If I were you, I'd hold off on the the dyes and wait it out.

 

The purpose behind the dye is to maintain the color of the dark stain and being able to use the wood without aging. Aging is used for clear wood where you may want to see the brown streaks. The dye maintains the color so that when the wood ages the underlying colors dont change the overall appearance of the dark stain over time. Like with maple the red undertones fade over time if stained dark the dark stain will appear lighter as the red undertones fade thus why you spray with a  green ish dye or lacquer stain as an equalizer.

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.