Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Newb needing to finish grill table.

Featured Replies

I need to finish a cypress big green egg grill table.  It will be sitting on our front porch which at times will be exposed to the elements depending on the how hard and which way the wind blows.  Sunlight partially but rarely direct.

 

I have read so much my head seems like it will explode.  Hoping you guys can help me out.  Right now condisidering using either General Finishes Outdoor oil, or Old Masters exterior penetrating sealer.

 

But after reading thinking about the CPES but who knows.  SInce it will be exposed to grease or bbq drips not exactly sure.  Let me know your thoughts. Thanks!

 

 

Either one should work. Or you could use Waterlox. I built my table to hold 2 big Green Eggs out of teak and brass screws in 1995 and never put a finish on it. It weathered to a gray patina and it stands on the back deck in the open. Cypress is a good outdoor wood but it is softer so the big requirement is ease of refinishing or renewing the coating. Don't try to build a film, just renew when it starts looking dried out.

I like the idea of General Finishes outdoor oil. The key is to apply it correctly and not build-up a thick film. I'm thinking anything with a film is going to lift from the heat of the BBQ. Get the outdoor oil down into the wood so it becomes part of the wood offering some protection. As to the sun and rain...how about a cover to put over that bad boy when not in use.  

 

-Ace-

The BGE shouldn't put out nearly as much heat has your typical grill, especially if you're primarily working at smoking temps. But there's still enough heat for it to potentially be an issue long-term. While I think a renewable finish is always a decent choice (for folks who don't mind the maintenance), I think a thin film finish could also be a viable option. If the film isn't super thick, it can still penetrate the fibers and prevent staining better than your average renewable oil. Or at least it will give you enough time to wipe up any spills. And because the film is so thin and fully absorbed, it isn't really going to act much like a film in terms of peeling. If it starts to look cruddy in a few years, give it a light sanding and re-apply. 

 

You can use just about any marine varnish or comparable product for this, but I'd recommend you thin it at least 50% for the initial application. 

 

And most importantly, please post a picture when you're done. I'm a Primo owner myself but I love seeing what people do with their Kamado grills!

I'm glad I came across this. I have two side table that I am redoing in wood. They were some cardboard type of material that just fell apart. I have a built in gas grill that runs off of natural gas. Unfortunately it isn't covered, what wood would y'all recommend?

CPES works very well as a primer, but it has no UV resistance at all.  However, it can still help you.  If you are going to use a marine varnish, put a few coats of CPES on first.  When it is dry, but not yet fully cured, begin your application of varnish.  As the CPES completes its cure, it will chemically bond with the varnish coats, improving their longevity.

 

The varnish will still need to be maintained, but it will be easier.  About once a year, maybe less, hit it with a sander, say about 180 grit or so... Then add a few more coats...

  • Author

Thanks for the info.  Couple decisions I guess I need to ponder.  Maintenance part for me will be a little bit of issue.  The ceramic egg is heavy and cumbersome.  Once I get it in there don't wanna move alot. It won't be going to the shop for any updates.  I will prolly get some kind of cover, although they get alot of use so covering and uncovering is often a pain. 

 

Ashamed I bought the table instead of building but for what I paid I don't believe I could justify the labor and materials for I paid. Cutting out the circle would require me to buy (another tool - not necessarily bad).  Not having to sand was huge as it has to be the worst part of any project for me. 

 

I will post a pic when I decided what direction to go.  I would like to spray on if at all possible - any reason not to?

 

Primo is a great grill too.  Neighbor scored a 1400 XL primo for 500.  HUGE.  He also bought a table from them since we were getting a deal.  While I would say I am an "Egghead" I do believe the style of cooking is whats best not the vessel.  Thanks yall

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.