Bombarde16 Posted May 2, 2014 Report Posted May 2, 2014 I'm working on a small Krenov-style smoother and wondered if there's any standard formula for the angle of the wedge. Quote
mds2 Posted May 2, 2014 Report Posted May 2, 2014 Not that I am aware off. I just taper them a bit for a super snug fit under the cross bar. Quote
Dave H Posted May 2, 2014 Report Posted May 2, 2014 Now I've never built a wooden plane, I have read Fink's book I don't remember a specific angle for the wedge but I was looking at some images of wooden planes and, they all seamed to be at a fairly shallow angle. https://images.search.yahoo.com/search/images;_ylt=A0SO8wQK1GNTnWQA4cRXNyoA;_ylu=X3oDMTB0YzIxdWM2BHNlYwNzYwRjb2xvA2dxMQR2dGlkA1ZJUDM1OF8x?_adv_prop=image&fr=yfp-t-901&va=wedge+angle+for+wooden+planes Quote
Bombarde16 Posted May 2, 2014 Author Report Posted May 2, 2014 Indeed, but how shallow? One can glean from Kari Hultman's site that her last project (a horned smoother named "Sven") had a wedge of 67-55=12 degrees. Presumably, a shallower angle makes the wedge less likely to work itself loose at the cost of needing more travel to get the correct pressure. That extra travel means the far end of the wedge will start to approach the mouth and become a clogging hazard. Quote
mds2 Posted May 2, 2014 Report Posted May 2, 2014 Indeed, but how shallow? One can glean from Kari Hultman's site that her last project (a horned smoother named "Sven") had a wedge of 67-55=12 degrees. Presumably, a shallower angle makes the wedge less likely to work itself loose at the cost of needing more travel to get the correct pressure. That extra travel means the far end of the wedge will start to approach the mouth and become a clogging hazard. Are you making a wedge like this? Or one that goes under a cross pin? If its the latter, just shorten it if it clogs. On these I just cut an approximate shape for the wedge, then sand it to fit. All I am looking for is a tight fit. 1 Quote
Dave H Posted May 2, 2014 Report Posted May 2, 2014 I checked out David Finks book from the library a couple years ago it was very informative. http://www.davidfinck.com/book.htm it's called Making And Mastering Wooden planes. Quote
Eric. Posted May 2, 2014 Report Posted May 2, 2014 Krenov makes no mention of the exact angle, only "a wedge that is pleasantly shaped; one with a low angle." The cross-pins on Krenov's planes were not round...they were only round at the tenons to fit into the holes. The rest of the pin was carved down to what I can only describe as a "faceted oval." I'll quote out of Fine Art of Cabinetmaking... "Make the cross-pin - in fact, make several, because it is so easy to spoil one. Have it square or rectangular at first and saw the tenons square, then round these to fit the hole. Shape the pin nicely. It should be a snug fit, though not too tight, since this pin moves slightly to follow the exactly slope of the wedge." So presumably, he would start with a general shape for a wedge, then refine it to fit. Looking at the photos in this book, his wedges look to have a consistent taper about halfway up, then they kind of transition into a gentle concave curve. Quote
derekcohen Posted May 4, 2014 Report Posted May 4, 2014 Use 10 degrees. That is pretty typical. A wedge with a high angle will not hold well. A wedge with a low angle does hold well. I assume that you are using a proper Krenov pin? A round dowel is a poor substitute - it will dent the wedge and then this will cause the wedge to be poorly secured. http://www.inthewoodshop.com/ShopMadeTools/BuildingaKrenovSmoother.html Regards from Perth Derek Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.