pastimage Posted May 10, 2014 Report Posted May 10, 2014 Ok, so ablaut two years ago I got a barn someone wanted torn down. Most of the wood was oak. I built an office and a back porch. I still have a lot of wood sitting out as flat as I can keep it and want to use it to make some shelves and such. I need to mill most of it down and the real question is what should I buy to do this with? Now keep in mind that most pieces are 1" thick and I am by no means a wealthy man. I get by because I can do my own work and will try anything. I have been to lows and home depot and I have read some "best of" threads but I wanted to come here and ask you. Obviously, I need to mill this flat and make it pretty but what can I throw out on the ground or on a makeshift workbench in order to do what I want. and can I do it for under a grand? I would prefer to do it for about 600 or less. Oh and I don't have space for many more pieces of equipment. My work shed is crammed full of stuff. Thanks in advance! Quote
krtwood Posted May 10, 2014 Report Posted May 10, 2014 You need a planer and a way to make one face so that it doesn't rock. A planer can deal with some kinds of non-flatness, like cupping, if the stock is thick enough (which yours is) but it can't eliminate twist or bowing. It doesn't sound like you have the room or the budget for a jointer so I would suggest you pick up an older stanley #5 hand plane which will be dirt cheap or if you want to splurge you can get a new one from Lee Valley in the $200-$250 range. The top end portable planers are $600 so you could put all your money there instead. With the hand plane you aren't looking to do anything but get rid of the high spots on one face so it doesn't need to be a finely tuned plane or have a well practiced technique. There are other ways of flattening a board without a jointer too. You can make a sled that you shim the board on and run through the planer that way. Again the point is to make it so the board can't rock or to hold the bowing in place so that when it passes through the planer the side facing up become flat. The longer the board the more a PITA it would be to do with a sled. Quote
EdgewaterWW Posted May 10, 2014 Report Posted May 10, 2014 Good info from Krtwood. Like he said there are other ways to mill lumber. Check out Marc's video http://www.thewoodwhisperer.com/videos/episode-6-the-jointers-jumpin/ and http://www.thewoodwhisperer.com/announcements/tww-rewind-the-jointers-jumpin/ More then just using a Joiner. Quote
pastimage Posted May 10, 2014 Author Report Posted May 10, 2014 @ krtwood The planks are from 8-10 feet long or longer. Most of what is needing to be removed is the very old and worn part so I can get back to some nice grain. Imagine seeing a 100 year old barn and you have my wood look and texture. I thought about the router and sled trick and that is a major pita. Wile the width is only 6-12" the length is what kills it. I am not sure I can make a plate in order to glue down and keep the wood from rocking, so I was with hope that a prattle might do the trick. I guess some of the wood will be cut down in time and I could do that up front for my ease, but even by the time I do that I will have 3-4' lengths to glue on a bed. Wonder if I soaked the planks for a while if that might help some? @Doug- Thanks for the links. I have been looking at many of the vis in order to get more ideas, perhaps I missed something. I will look again EDIT** @ krtwood What portable would you recommend? (anyone can jump in on this question too) From what I have I can cut out any twists and bows, I think. I will be working both flat sides so I am thinking that is the way to go. thoughts on the makita 2012NB? Quote
..Kev Posted May 10, 2014 Report Posted May 10, 2014 http://www.grizzly.com/products/12-1-2-Planer/G0505 Inexpensive lunchbox planer that takes a beating and keeps milling. Blades aren't too expensive either. I've had one in my shop for a few years and can't seem to break it. I've run a bit of barn board thru it as well. Good luck! Quote
krtwood Posted May 10, 2014 Report Posted May 10, 2014 The Makita is what I have and I can't really compare it to anything else. The Dewalt has a sort of built in dust collection fan that you can run a hose into a garbage can and get a lot of the chips. You'll be ankle deep in chips real quick without some way of managing the chips they spew everywhere without dust collection. The DC adapter that Makita makes is crap, I made my own. Quote
pastimage Posted May 11, 2014 Author Report Posted May 11, 2014 You'll be ankle deep in chips real quick without some way of managing the chips they spew everywhere without dust collection. I really need to set it up in my garden after growing season! = ) I like that the mikita is quiet. The desalt is WAY TOO LOUD. I saw a video of it and had to mute it. Not impressed. I do like the 3 blades and flip them and keep going but in the long run I don't think it will be what I want. I found an in box woodmaster for like 1200, but room... Not sure about the grizzly. Quote
RichardA Posted May 12, 2014 Report Posted May 12, 2014 Two points: Buy a good wire brush and brush the hell out of both sides before you slip it in any planer... I have a dewalt 735 and in less than 150 feet of barn wood I had to replace the blades, grit, dust all kinds of crap gets in that wood! the 735 is a good tool but after you use up the factory blades {and you will, on barn wood} get a set of HSS blades from infinity tools! They're like a hot knife through warm butter! Quote
CT Proctor Posted May 12, 2014 Report Posted May 12, 2014 Buy a metal detector and scan the boards first, your new planer knives will thank you. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.