mrplow999 Posted December 26, 2014 Report Posted December 26, 2014 Hello all, long time lurker, first time poster. Just inherited a Powermatic PM66. Pulled the top to clean it up and found one of the trunnion supports cracked. What are my options here? Am I hosed or can it be fixed? I've heard very few success stories welding cast iron, but I don't think that Powermatic is selling replacement parts anymore so I'm not sure what options I have. Also, if someone in Phoenix knows a good welder whom they think can do the job, chime in please. Thanks Jy Quote
wdwerker Posted December 27, 2014 Report Posted December 27, 2014 I would check on the Old Woodworking machine forum, they will know! Only old American machines is their limit. I had to replace the trunion on my UniSaw a few years back, but that was before they got sold to the Chinese . I got my parts from Saw Center Quote
Tom King Posted December 27, 2014 Report Posted December 27, 2014 There are companies that specialize in it. http://www.locknstitch.com/Default.htm Quote
dwacker Posted December 27, 2014 Report Posted December 27, 2014 Did you call powermatic looking at the color the saw is not very old. They don't break usually a bad casting. They may have some old inventory. Quote
sjeff70 Posted December 27, 2014 Report Posted December 27, 2014 I would check on the Old Woodworking machine forum, they will know! Only old American machines is their limit. I had to replace the trunion on my UniSaw a few years back, but that was before they got sold to the Chinese . I got my parts from Saw Center http://www.owwm.org/viewforum.php?f=1&sid=7599cb15d3c82e0131e08e4ad1ea79b5 Quote
mrplow999 Posted December 27, 2014 Author Report Posted December 27, 2014 Thanks for the reply's. I had thought about OWWM, but since my saw was made in 2000, I didn't think that it really qualified as 'old'. I'll give a post a try there. I did contact Powermatic and got a very helpful individual that made the suggestion regarding welding it. I just want to make sure that it gets done right. I would really hate to trash thi saw, it's in such good shape other than this. Quote
Raefco Posted December 27, 2014 Report Posted December 27, 2014 It can be fixed (welded) if you can find a small local welding shop it shouldn't be that big of a deal. It's maybe a few hour repair plus material and shop cost, the filler rod is some what expensive. The cracks would need to be V'ed out and the pieces pre heated before welding and heated once again after welding, Or it could be brazed, same deal but using a softer filler metal such as brass or bronze, either way, it could be machined when done so the repair would be barely detectable, depending on time and money spent Quote
mrplow999 Posted December 27, 2014 Author Report Posted December 27, 2014 That's what I'm hoping. Hard part is finding the shop. I've got a few feelers out right now, but most of the places I've contacted seem leery of welding it. The majority or responses have been cool at best as soon as I mention cast iron. Quote
tim0625 Posted December 28, 2014 Report Posted December 28, 2014 Mrplow999....WELCOME!!! Good place to come and hang and ask questions. Is the trunnion a cast iron or steel? Cast iron like well pump heads have to have some special treatment - special welding rods or either brazing to fix a crack and the brazing may require an old timer with some gray hair. It used to be done more but not so much now. Steel can just be welded - wire or stick or even TIG'd and most shops can do this. But....like Steve and PB suggested...finding an old trunnion somewhere would be best. Don't trash the saw over it. Maybe Ebay? if it's a 2000 model, there's a trunnion somewhere. Quote
JerrySats Posted December 28, 2014 Report Posted December 28, 2014 I'm surprised you can't get parts from PM , looks like a pain to take a part is it ? Quote
mrplow999 Posted December 28, 2014 Author Report Posted December 28, 2014 Overall, it's not too much a pain to disassemble. I did the same with my old Delta Uni a couple years back. The hardest part is really removing the motor. It's pretty heavy. I had considered pulling it apart already to do a good clean up on it, now it looks like I have to. I really only got steered in the welding direction because that was what the guy at Powermatic suggested. I have a few feelers out for a replacement support, but the cost will most likely be the factor. According to one site I found that support was approx $500. If I can repair it for $100 or so, that't the route I want to go. Got a quote from the Lock-n-stitch guys for $125 (furnace braze), but I'll have to ship it to CA. Not really wanting to ship it, so I'm trying to find something local now that I know it can be done. I posted this same question over on Lumberjocks and got the suggestion that I JB Weld it. Kinda leery of that. The area where it's cracked is where the majority of the weight of the motor is. It would suck pretty hard to have the thing let go while I was running lumber through it. JY Quote
tim0625 Posted December 28, 2014 Report Posted December 28, 2014 Negative ghost rider on the JB Weld...not with that long term vibration. Take the trunion off...take it around to the local metal working shops and ask if they have any people who know how to braze things. It may be an old timer but you could probably get it done for $100 or $125 without the shipping costs. Quote
Raefco Posted December 28, 2014 Report Posted December 28, 2014 its really hard to tell how bad, or how long the crack has been there till the piece is removed. Will the unit fall into multiple pieces when removed and how hard will it be to get lined up if it does? I could do it, but that does not help with the shipping and the question, "will it work" after welding/brazing it blind. If I were trying to locate a specific craftsman to fix something such as this I would try to find a local supply house that carries their consumables and ask around. something like thishttp://www.phxwelding.com/locations.htmor a praxair, airgas. mittlers… Quote
tim0625 Posted December 29, 2014 Report Posted December 29, 2014 If it falls into two pieces [probably won't], they will go back together neatly like anything cleanly broken. I think someone said it earlier....a metal working guy (or girl ) will grind out a V on the crack not only to clean the crack area but it's for the brass to fill up. I'm assuming the trunnion is cast iron. He will use the torch to heat the entire area to 'the right temperature' and then apply the brass and melt it in the V. The case iron has to be the 'right temperature' to accept the brass and bond with it. Here in SC, we can have a cold snap that freezes and splits the pump head on a well pump. It's cast iron and some of the older metal workers have repaired them for years but it's usually one older guy in the shop who knows how to do it. There are cast iron welding rods but there again...that usually requires someone with experience using them. Don't over-complicate this by looking for specialty companies. Take your trunnion around to some of the smaller metal working shops and ask if they have someone experienced in brazing cast iron. Heck...I can do this for you but I know a few old timers here who are better than me. If you find that there is no one in the Phoenix area who knows how to do this, ship the trunnion to me and I'll get an old timer here to do it. (I think I'm safe...Phoenix is pretty big - you can easily find someone there) Quote
mrplow999 Posted December 29, 2014 Author Report Posted December 29, 2014 Thanks guys! I'm going to start calling around and see whats what tomorrow. I'll have it pulled out by the weekend and I'll report back I'm sure someone here in town can do it, I think your probably safe Tim JY Quote
wdwerker Posted December 29, 2014 Report Posted December 29, 2014 Take lots of pictures as you disassemble it ! Trust me you may need them. I keep a stack of zip lock bags and a Sharpie handy to store small parts and label them. Take notes and get real methodical it can save you lots of grief when you finally put it back together. It's those days or weeks before reassembly that lets the little details slip your mind. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.