Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

aluminum oxide or zirconium on my drum sander ?

Featured Replies

The zirconium runs 200 dollars from supermax which is 70 more than a comparable roll of aluminum oxide paper. I use a supermax 19-38 and I sand a bit of end grain but mostly just standard home drum sander usage.

The zirconium is great abrasive, but pricey. If you are vigilant about keeping it clean the aluminum oxide does the job just fine, and cheaper. I only spring for the zirc when I had a ton of sanding to do with a single grit. I keep 36 to 220 and everything in between in the aluminum.

I'd find a better supplier. The difference should not be that much. Longer cut your own rolls cost more up front but save much more in the long run.

  • Author

Thanks guys. Any supplier suggestions I want to order a nice assortment of full rolls so I don't have to stop a project or wait.

Thanks guys. Any supplier suggestions I want to order a nice assortment of full rolls so I don't have to stop a project or wait.

 

Try Klingspor. If you have self tensioning drums you can use 4" but have to call. If no self tensioning then they should list 3" on the web. 

  • Author

Terrific I will price them both. My planer died today damn...

I can't recommend them. I have a single wrap of 100g Klingspor that has out lasted a full roll from IA and the IA has only been used on the outboard drum. You sort of get what you pay for with sanding abrasive within limits of course.

I can't recommend them. I have a single wrap of 100g Klingspor that has out lasted a full roll from IA and the IA has only been used on the outboard drum. You sort of get what you pay for with sanding abrasive within limits of course.

I use Klingspor PS33 discs and they are great but I have never used their drum sander paper. I'm not doubting the Klingspor is better paper but 1 wrap lasts longer than 20 wraps from a full IA roll? I use a paper cleaner stick on mine frequently and IA paper last a long time. I only use 120 on mine and lights passes. 

I use Klingspor PS33 discs and they are great but I have never used their drum sander paper. I'm not doubting the Klingspor is better paper but 1 wrap lasts longer than 20 wraps from a full IA roll? I use a paper cleaner stick on mine frequently and IA paper last a long time. I only use 120 on mine and lights passes. 

 

I only use 25 or there abouts yard rolls. If you use the sander properly and run through the grits 5 wraps from 25 yard rolls will last a very long time. I would guess years in a hobby shop. 5 wraps rotated  is enough to complete 80 + full sets of kitchen cabinets with quality paper. The 220 step doesn't last as long but its not much worse. If your not stepping though your grits your wasting the rolls and discs on the finish sanding side. 120 is closer to 100 maybe even 80 on your RO depending on the rolls you buy. If you run down to 220 on the drum then your at 180 on the ro to do your finish sanding. Its sort of a pain to switch grits on a single drum but if you do you will save abrasives on both ends.

I only use 25 or there abouts yard rolls. If you use the sander properly and run through the grits 5 wraps from 25 yard rolls will last a very long time. I would guess years in a hobby shop. 5 wraps rotated  is enough to complete 80 + full sets of kitchen cabinets with quality paper. The 220 step doesn't last as long but its not much worse. If your not stepping though your grits your wasting the rolls and discs on the finish sanding side. 120 is closer to 100 maybe even 80 on your RO depending on the rolls you buy. If you run down to 220 on the drum then your at 180 on the ro to do your finish sanding. Its sort of a pain to switch grits on a single drum but if you do you will save abrasives on both ends.

 

Wow that is a lot of use, really?

 

However, at some point you would think the abrasives wear out and not cut the wood as it should, ya know, when your trying to sand with dull sandpaper, it takes forever. Works the same way on a drum sander.

 

-Ace- 

Wow that is a lot of use, really?

 

However, at some point you would think the abrasives wear out and not cut the wood as it should, ya know, when your trying to sand with dull sandpaper, it takes forever. Works the same way on a drum sander.

 

-Ace- 

 

Sanders are for surface prep. Using a single abrasive and lowering the drum or raising the table between passes is abrasive planing not sanding. Grits like 120 are for surface prep. 24,36 or 38 are more reasonable for surface planing. The difference between grits for surface prep is .006 anything more your dulling the wrap prematurely.

Sanders are for surface prep. Using a single abrasive and lowering the drum or raising the table between passes is abrasive planing not sanding. Grits like 120 are for surface prep. 24,36 or 38 are more reasonable for surface planing. The difference between grits for surface prep is .006 anything more your dulling the wrap prematurely.

:huh:

 

Not sure what this statement has to do with abrasives wearing out? 

 

-Ace-

  • Author

.006 of material removed in grits higher than 80 you mean ?

.006 of material removed in grits higher than 80 you mean ?

No. Let's say your first pass is with 80g and your second is 100g then you move your drum .006 closer to the wood on the second pass.

Terrific I will price them both. My planer died today damn...

.

Are you replacing it or having it fixed

Oh I see thanks is there a chart for this formula?

 

I don't know of a printable chart. Its usually a built in function of all multi head machines. Most big shops will run two triple head wide belts connected by conveyer so that its just one pass down to 220 with .006 difference in height between grits. Even my little dual drum has the same feature.

  • Author

Thanks kcooper j got a 735x with a byrd head coming it's the best I could get with my remaining shop space. The supermax took up more space than I expected. Lol

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.