Janello Posted April 5, 2015 Author Report Posted April 5, 2015 Depends on what kind of stuff you build. Having built a guitar and going to be starting another one in the next 3-6 months, there's an ungodly amount of jigs and special tools needed for the task. Can't just leave everything out and about. Right now most of them are in a rubbermaid tub in my basement because there are no cabinets in the shop to hold them. I see your point. It's just personally speaking, storage space for small items will not be an issue for me as much as floor space for machines. I have the whole 12x24 finish room for storage. Quote
Popular Post Eric. Posted April 5, 2015 Popular Post Report Posted April 5, 2015 To each his own. I use my SCMS on every project, and the cabinets beneath it are stuffed full with things I use constantly. Everyone works differently...if you don't need cabinets or a miter saw, say buh-bye and move on. On the other hand, I can't fathom a shop that doesn't need drawers and cabinets to store things...unless you only build one thing over and over again. Hobbyists tend to have a million different toys because they build a spectrum of projects. If I didn't have cabinets, it would be a gargantuan cluster-you-know-what in here and I'd hate my life. 3 Quote
dwacker Posted April 5, 2015 Report Posted April 5, 2015 I don't know that it's a matter of need which is whole point. I doubt anyone really needs all the stuff that gets hoarded. I can build most anything in my shop and have three wall cabinets and three drawers and nothing gets left out except a pencil. I would just put some real thought into what goes into the shop since you have the luxury of starting off with a clean slate. Try putting painters tape on the floor to mark out locations. Think about things like sandpaper. Does it really need a big ass organizer system. Do your six or eight router bits really need a dedicated drawer when a butter dish works just fine. All this stuff eats up space. Try going without the miter saw for awhile if it's not a good fit then go back to using it. It ultimately a personal preference not a matter of need. Quote
Janello Posted April 5, 2015 Author Report Posted April 5, 2015 The comments here were helpful to hash things out in my mind. I tend to see both sides as valid. Those who use one regularly and those who don't use one at all. I waver somewhere in the middle, so I think a compromise is what I will eventually settle on. Keeping one in my workflow, but making it smaller and mobile. Happy Easter All! Quote
Cochese Posted April 5, 2015 Report Posted April 5, 2015 To each his own. I use my SCMS on every project, and the cabinets beneath it are stuffed full with things I use constantly. Everyone works differently...if you don't need cabinets or a miter saw, say buh-bye and move on. On the other hand, I can't fathom a shop that doesn't need drawers and cabinets to store things...unless you only build one thing over and over again. Hobbyists tend to have a million different toys because they build a spectrum of projects. If I didn't have cabinets, it would be a gargantuan cluster-you-know-what in here and I'd hate my life. There it is. Pretty much agree with this in whole. I wish I had about 3000 more cabinets to store all this stuff I have in, and I don't even have that much. I have almost zero jigs, but would love to make about fifty just off the top of my head. So much that I can't do just because I don't have the space to store the tools and setups required to do so. Half-round hall table? Hell no, no space to keep the bending form, and I'm not throwing it away after using it once. Drawers are damn useful, too. I'm making one in my new storage wall just for clamps for the MFT. I know some guys that have about ten routers. Cabinets. Several circ saws. Cabinets. There is never only one way to woodwork. Quote
CessnaPilotBarry Posted April 5, 2015 Report Posted April 5, 2015 I don't have a miter saw in the shop. I break down stock with a jigsaw. I miter saw gets used outside the shop only. Quote
Brendon_t Posted April 5, 2015 Report Posted April 5, 2015 I have a miter saw in the shop. It sits on a shelf collecting dust until I need to trim out a door or window that is not in my house. I break my rough lumber to length the old way. Hand saw and chalk line. Long rips are done on the band saw. If I had a 12 foot section of cabinets on the ground, I doubt I would dedicate that space to cutting long boards. I like bench top tools. In that section, I could plant a HCM, table top dill press, grinding station and about 6 feet left over 1 Quote
bgreenb Posted April 6, 2015 Report Posted April 6, 2015 I know I'm late to the party here, but I use the miter saw similarly to the OP (mostly just breaking down larger stock), and here's my solution. This miter stand was my one of my first ever "woodworking" projects. I had bought a miter saw to do some DIY stuff around the house, and it was frustrating not to have a stand for it (and a longer fence). I found these plans online and built the entire thing with a circular saw, a couple of C clamps, and a router for the dadoes (that I bought expressly for this project). It's FAR from the best miter stand of all time, but it folds up nicely and takes up very little space (the wings tuck back and the fences fold down on piano hinges) and has some storage underneath for my nail guns and a couple systainers, as well as some random cutoffs. It tucks away against the wall when I'm not using it. It took me a while to build because I had no idea what I was doing but it's realistically an easy weekend project. I believe I still have the plans floating around and I can email them to you if you're interested. Quote
Janello Posted April 6, 2015 Author Report Posted April 6, 2015 Looks like that would work out good. I will PM you my email address. Thanks Brian. Quote
PlaneAndDestroy Posted April 9, 2015 Report Posted April 9, 2015 What do you need storage for in a dedicated shop? More tools of course! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.