Bombarde16 Posted April 8, 2015 Report Posted April 8, 2015 This is the column for a maple pedestal table made by the Eastern Butcher Block company back in the 1980s. I'm refinishing the top and, while I've got it apart, wanted to lighten the boxy and clunkiness of the column. Running a chamfer with a router is easy, but stopping a chamfer produces a lopsided termination: one side is curved and one side is straight. The solution is to carve a proper termination by hand. Personally, I like lamb's tongues; but in deference to the overall modern lines of the table, I'm stopping these chamfers with a simple, angled cut. Six down, ten to go. Sent from my iPhone using Tapatalk Quote
Tom Cancelleri Posted April 8, 2015 Report Posted April 8, 2015 Sounds like you need a shaper 1 Quote
wouldwurker Posted April 8, 2015 Report Posted April 8, 2015 Very cool, Rob. Thanks for posting. Quote
Tom Cancelleri Posted April 8, 2015 Report Posted April 8, 2015 actually couldn't you setup a 4 sided stop block and just reference off each side to even out the chamfer from both sides Quote
bgreenb Posted April 8, 2015 Report Posted April 8, 2015 actually couldn't you setup a 4 sided stop block and just reference off each side to even out the chamfer from both sides Yup. I've done this (though I do it at the router table - you just flip the piece end for end and run it again, but same idea). Quote
Brendon_t Posted April 8, 2015 Report Posted April 8, 2015 Hitting it from both sides is where my head was going also. There may be a slight ridge down the middle that could easily be knocked off with some hand sanding. Quote
davestanton Posted April 8, 2015 Report Posted April 8, 2015 I have to take my hat off to you guys. If you hadn't drawn my attention to it I would have thought it was fine to just do the chamfer with the router and then sand it. Once the lines had gone there would be no real reference to draw my eye to it. Especially if it was near the base of the leg or even near the top hidden slightly by a larger counter.But hey, that might just be me. 1 Quote
CessnaPilotBarry Posted April 9, 2015 Report Posted April 9, 2015 Wait... a spinning round tool can't leave a flat line on more than one plane? I can't do a lamb's tongue with a router? Quote
dwacker Posted April 9, 2015 Report Posted April 9, 2015 Wait... a spinning round tool can't leave a flat line on more than one plane? I can't do a lamb's tongue with a router? Cylinder vs cone. A straight cutter would make both sides the same. Tack a square block on the ends and tip on edge or just use the jointer. 1 Quote
Bombarde16 Posted April 9, 2015 Author Report Posted April 9, 2015 Sounds like you need a shaper ...or a router table with a long, straight bit and a cradle to hold the stock at 45 degrees. That would be very cool, but it would limit you to one sort of termination: i.e. a concave curve defined by the radius of the cutter. The inside of that curve would likely be marred by burning, tearout, or both, necessitating some one-by-one cleanup regardless. Given a choice between the finger numbing grind of sanding out burn marks or chopping them away with a chisel, I'll take the latter. Moreover, this wouldn't be possible on this piece, which is already glued up with other boards into an X-shaped column, rendering the whole question moot. It's really not hard to terminate a chamfer by hand. All easy, downhill cuts following the layout lines and you're done. Frankly, it's relaxing work and it's a great way to get your feet wet in carving. I have to take my hat off to you guys. If you hadn't drawn my attention to it I would have thought it was fine to just do the chamfer with the router and then sand it. Once the lines had gone there would be no real reference to draw my eye to it. Especially if it was near the base of the leg or even near the top hidden slightly by a larger counter. But hey, that might just be me. It's a matter of size. With small chamfers or roundovers, the difference is so slight as to be irrelevant. On larger pieces, it does become noticeable. Quote
Tom Cancelleri Posted April 9, 2015 Report Posted April 9, 2015 You could have finessed the termination point of with an oscillating spindle sander as well Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.