Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Bandsaw blade too loose with no tension?

Featured Replies

Earlier this year I bought a Jet 14" bandsaw off CL and finally getting around to tuning it since I have to cut some curves soon. One thing I noticed when putting on a 93 1/2" blade is it is very loose with no tension on the spring. When I tension the spring appears to compress before all the slack is out of the blade. With a 1/4" blade the spring is almost fully compressed and it still doesn't seem to have enough tension. With my past bandsaws the blade went on with just a little slack so I'm assuming this is what I want. Since this is a 93 1/2 blade which is recommended for the saw it could be the distance between the wheels is a little off. Is there a way to adjust this? I glanced at the manual and didn't a way. If not then it sounds like plan B would be to get a smaller blade? If that is the case do I just cut the existing blade, use my hands to take the slack out and measure the amount of overlap, then subtract that from blade length?

Maybe the previous owner kept it tensioned all the time which could possibly bend the arm some? I did put a new Carter spring in it and the problem still persists so I should have eliminated a bad spring as the problem. 

I think I'd start by confirming that the blade is actually the length that you ordered; could have been an oversight with shipping.  It's pretty unlikely that the wheels themselves have been pulled closer together.  If they seem to turn freely without any funny sounds in the bearings I'd initially rule that out.  Where did you get the blade from?

  • Author

The blade came with the saw and was unopened Ridgid blade. No funny sounds and wheels spin freely. 

I also have a Jet 14" bandsaw, but it uses 105" blades so I'm fairly certain we're talking about different models. That said, on mine there is a bushing with a set screw that can be tightened/loosened to adjust the tension if the adjustment using the little blade width gauge isn't getting you what you want. You basically loosen the set screw with an allen wrench and then use a pair of pliers to turn the bushing on the threaded rod, then tighten the set screw. If you've only adjusted the tension using the knob and haven't look into adjusting the bushing, it might get you where you need to be.

I'm probably describing this horribly. Check out page 14, steps 6 - 9. I realize that this isn't the same model, but the mechanism on yours might be similar: http://content.jettools.com/assets/manuals/710116K_man_EN.pdf

 

  • Author

Can you put some washers under or over the spring ? Anything to move the wheel up before you tension it.

Couldn't figure a way to use washers but I came up with this and it worked great. Not the sexiest solution but did the trick.

B7CA8609-2B62-4740-8BFF-3644F6E18166_zps

I looked at it from about 4' away and it looks sexy to me. But to me, I think Martha Stewart is hot!

Edited by K Cooper

When I got my new Grizzly it was the same way. 93 1/2" blade and wouldn't tighten up. I had to loosen the nut and back off the stop. It didn't take much and the blade tightened up nicely.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.