Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

My Polyurethane Screw Up

Featured Replies

The other night I made a big mistake while applying polyurethane to some drawers I've been working on.  I had my mask on and couldn't smell anything but once done I took the mask off I found the terrible smell of oil based polyurethane.  I thought I had grabbed my can of water based polyurethane but apparently I accidentally switched them somewhere along the way when I was getting the cans out.

So now the drawers have 1 coat of oil based poly on them and stink.  These drawers will be used for clothes so I'm concerned that they will cause the clothing to stink too.  I've been looking online for a next step to remedy the smell and I've seen it suggested to put down a second and third coat of water based poly over the 1st coat of oil poly.  Mostly these suggestions were of people talking about hardwood floors.  The theory is that it will lock in the smell and give the desired finish I was looking for.

My question to the forum is, would this be a wise step or should I do something else?  Has anyone ever covered oil based poly with water based?  Thanks for any help and suggestions.  I'm really kicking myself over this simple mistake.

You can do it most of the time, but you'll need to allow the original coat to fully cure; most recommend at least 72 hours at room temps.  To be on the safe side, it might be a good idea to make a scrap piece the same as you did on the drawers and use the water based on that BEFORE taking it to the drawers :-) 

It also might be a good idea to give a coat or two of de-waxed shellac before applying the water poly.

  • Author

You can do it most of the time, but you'll need to allow the original coat to fully cure; most recommend at least 72 hours at room temps.  To be on the safe side, it might be a good idea to make a scrap piece the same as you did on the drawers and use the water based on that BEFORE taking it to the drawers :-) 

It also might be a good idea to give a coat or two of de-waxed shellac before applying the water poly.

Thank you for your suggestion and confirming that this process could potentially work.  I'll make up a couple spare pieces of oil poly and try the water poly on them first to make sure it works before going all in.

I'd be afraid that anything off gassing from the oil based layer may bubble the layer above but I have no idea if that is even plausible. 

I did the same a few years ago, only out of ignorance, not mask. After a few months there was no odor at all.

If shellac locks in the smell, wouldn't that alleviate the need to put water based poly over it? 

I know you can apply water poly over oil base, but I wouldn't apply shellac over poly, I always use that as first coats. Not sure that is the best way but that is what I have experience doing. Sent from my Nexus 5 using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.