Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Simple Mitered Box: First Exotic and First Veneer

Featured Replies

  • Popular Post

My boss is retiring and is a wood turner so I decided to make him this box and get him a certificate to a local wood store with a bunch of turning blanks and stuff. He gave me my first job out of college at the place of my dreams and I was really grateful to him. The sides of the box are Honduran rosewood and the top is maple burl veneer. I chose the rosewood because I had lived in Honduras for a while and wanted it to represent me relocating to work at my current employment. I also wanted to do the veneer since I had never done that before to represent him taking a chance on me and hiring me for an area that I had no experience in but really wanting to do.

I have only been woodworking for a little bit with this my 3rd "fine" woodworking project (one of which was a similar style box). People are pretty familiar with putting the box together and then cutting off the top, which is what I did here. I made a 45 degree cross cut sled which made the sides a lot easier to use.  The glue up was done using tape on the outsides of the joints and then wrapped together. putting the tops and bottoms inset. After it dried I cut the top off so all the grain would match. 

For the veneer I put it on some 5mm laun plywood from the home center which was a bad idea. When I first cut it it was laying flat. Since it was so small and area I decided to use normal wood glue (and that is all I had). I glued up the panels and put some really heavy weights on them. The veneer seems to have held on nicely but I didn't make the boxes right away and after a couple of days they were super potato chiped. I was able to bend them into place during the glue up but when I cut the top off it warped somewhat as well. I did a bunch of sanding to flatten where the lid and body meet (i need to get a big powered sanding disk instead of a sheet of sandpaper on a granite tile). The veneer was pretty poorly sliced and while I was sanding it to get rid of the marks left on it i sanded through some of it. I cut down the panel to remove that and didn't sand much more so there are some milling marks. Probably shouldn't have used burl for my first veneer, cause it was a pain. I put two strips of the rosewood inside the box to keep the lid in place.

For the finish I used Watco natural danish oil. It looked great and I put on three coats. Then I noticed that it seemed to be weeping finish from some of the pores. I looked online and read you shouldn't use oil on rosewood. Woops. It seemed like after time it would stop but I didn't have much time before my boss left so I decided to wax the whole box which would hopefully push the finish out of the pores. I did two coats of wax but the next day there was still some weeping. Then I turned on a space heater by the box to 90 deg and buffed the box out every half an hour for about 5 hours. And then let it sit overnight by the heater. The next day I didn't see any weeping at all. It still had an odor (Some danish oil seeped around the lid into the inside and I don't think it cured or will very well. I should have prefinished the panels) but I had to hand it off. 

I was going to put some splines in the miters, but the panel seemed plenty busy enough that I decided not to. Hopefully since it is just a decorative box, the extra strength loss won't matter.

Any critique would be appreciated. (What do you think of wood types? Should I have used splines? Tips on this type of construction?)

 

Thanks!

 

P.S. I ended up buying like 15 bf of rosewood because they said if I take it all it could get it at 75% off. What is a good finish that give a nice close to the wood feel, but i can use on the rosewood?

image1.JPG

image3.JPG

image4.JPG

Nice box!  Unless it's being banged around a lot, I think you should be fine without splines.   

Not only is it a great box, but I think you're probably a first. This is the only time I've seen someone with only one post with 2 likes? Welcome to the forum.

  • Author

Thanks so much everyone. I think I am going to try shellac on the rosewood in the future. I have used shellac on some oak cabinets before painting before, but never with a rag. The mineral oil and shellac sounds like something I definitely want to try. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.