socoj2 Posted January 12, 2016 Report Posted January 12, 2016 In the next few weeks im planning on purchasing a G0490W , i wanted the Byrd head instead of the Grizzly spiral head but grizzly wont do a factory install. im slightly worried about my ability to do the install and get everything setup right. Anybody got any ideas on how difficult it is to get this setup? Or do i just need to bring FTR, vince or Steve to come help? Quote
bgreenb Posted January 12, 2016 Report Posted January 12, 2016 @Eric. did it, so I assume anyone can Seriously though, I think his proceeded basically without incident, except that one of the bearings he reused was bad. Don't think that would be a problem for you, since you'd be reusing completely unused bearings. Might be good to order some extras just in case though, for a few bucks of insurance. Quote
Eric. Posted January 12, 2016 Report Posted January 12, 2016 Yeah it's not that big of a deal. I would be more hesitant about the machine itself in general than the head install...but that's all I have to say about that. Even though you could reuse the factory bearings since they're brand new, I would buy two new higher quality bearings and install them with the new head. You already have it taken apart so why not while you're in there?....and just in case you damage one of the bearings trying to pull them off the factory head. But the process itself is fairly straight-forward. 2 Quote
minorhero Posted January 12, 2016 Report Posted January 12, 2016 Why are you removing a grizzly spiral head and installing several hundred dollars of Byrd spiral head? I have used Byrd heads before and seen the results of grizzly heads, admittedly I haven't used the grizzly myself. But if there was any difference I couldn't have detected it with my hands and eyes. Certainly not enough to remove a head and let it sit. Quote
socoj2 Posted January 12, 2016 Author Report Posted January 12, 2016 55 minutes ago, minorhero said: Why are you removing a grizzly spiral head and installing several hundred dollars of Byrd spiral head? I have used Byrd heads before and seen the results of grizzly heads, admittedly I haven't used the grizzly myself. But if there was any difference I couldn't have detected it with my hands and eyes. Certainly not enough to remove a head and let it sit. im not im going to buy the jointer with out a spiral head and put the byrd in it. Quote
Keggers Posted January 12, 2016 Report Posted January 12, 2016 I've had two Grizzly jointers both with spiral cutter heads. The first one was an eight inch model and I now have a twelve inch. Both have done a great job for me and I really never saw a reason to change the heads. Of course, I'd much rather work on wood than my machines. Quote
Tpt life Posted January 12, 2016 Report Posted January 12, 2016 Point missed after two clarifications. Let me try for him. He is buying a straight knife head and swapping it for a Byrd. Is that clear enough yet? Quote
rodger. Posted January 12, 2016 Report Posted January 12, 2016 Marc has a video on installing a spiral head cutter in a jointer. His is powermatic, but still should be worth a watch. Quote
Eric. Posted January 12, 2016 Report Posted January 12, 2016 Grizzly also has a video using the exact machine you're planning to buy (the old model anyway...don't know if they're making changes with the new one). I used this video as instruction when I did mine and it was sufficient. Here it is... Quote
Keggers Posted January 12, 2016 Report Posted January 12, 2016 34 minutes ago, C Shaffer said: Point missed after two clarifications. Let me try for him. He is buying a straight knife head and swapping it for a Byrd. Is that clear enough yet? I fully understood what the man was saying. My point was why not just buy one with the spiral heads already included since they do a great job. Clear enough? Quote
Tpt life Posted January 12, 2016 Report Posted January 12, 2016 There is a lot out there to read. I started digging when someone asked about the difference between Grizz spiral and Byrd shelix. Apparently the she stands for the shear angle of the insert. Guy decides he wants a Mazda for the Wankel and the response is "why not buy a Ford? It's good enough." You may be right, but he may prefer the Byrd. Quote
bgreenb Posted January 13, 2016 Report Posted January 13, 2016 4 hours ago, Keggers said: I've had two Grizzly jointers both with spiral cutter heads. The first one was an eight inch model and I now have a twelve inch. Both have done a great job for me and I really never saw a reason to change the heads. Of course, I'd much rather work on wood than my machines. 2 hours ago, C Shaffer said: There is a lot out there to read. I started digging when someone asked about the difference between Grizz spiral and Byrd shelix. Apparently the she stands for the shear angle of the insert. Guy decides he wants a Mazda for the Wankel and the response is "why not buy a Ford? It's good enough." You may be right, but he may prefer the Byrd. Jeez. Keggers was just clarifying why the OP was going the Byrd route and offering an opinion that he might get the same results a few hundred dollars and a few hours of his time richer. Not sure why that got your dander up so much. Maybe others will learn from listening to the OP's explanation of why he wants the Byrd. Who knows where it will go? Especially since the OP's question has basically been answered, why not get some other information out too? Quote
socoj2 Posted January 13, 2016 Author Report Posted January 13, 2016 11 minutes ago, bgreenb said: Jeez. Keggers was just clarifying why the OP was going the Byrd route and offering an opinion that he might get the same results a few hundred dollars and a few hours of his time richer. Not sure why that got your dander up so much. Maybe others will learn from listening to the OP's explanation of why he wants the Byrd. Who knows where it will go? Especially since the OP's question has basically been answered, why not get some other information out too? actually the price difference is like <$100 $1025 with no spiral + Byrd $409 - $1350 with Spiral So $1429 vs $1350 thats why i wanted it. Quote
Keggers Posted January 13, 2016 Report Posted January 13, 2016 I was just attempting to pass on information for whatever that information is worth based upon years of using Grizzly jointers with spiral cutter heads. I don't often offer an opinion but when I do it is given with the best intent. I'm sure the Byrd cutter heads are very good and Socoj2 will be very happy with them. Quote
Tpt life Posted January 13, 2016 Report Posted January 13, 2016 1 minute ago, Keggers said: I was just attempting to pass on information for whatever that information is worth based upon years of using Grizzly jointers with spiral cutter heads. I don't often offer an opinion but when I do it is given with the best intent. I'm sure the Byrd cutter heads are very good and Socoj2 will be very happy with them. Kent, I must have misunderstood your intent and truly didn't mean to be a jerk. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.