Recommended Posts

Posted

So I've been sharpening some of my saws. I built a "saw vice" to hold the saws cleanly in my vice - a big improvement from just shimming them in the vice.

The filing was no problem ... I've done that before.

But my question is the set. I've never set the teeth on a saw blade before, so I don't know how much set to give the teeth. Any ideas for a 4.5tpi rip saw and a 14 tpi x-cut carcass saw?

I've got the little saw-set shown in the picture - it should be good for the rip saw, but it looks a bit clunky for the carcass saw. I'd rather leave the set alone than ruin my saw by mangling it in the wrong tool. Any ideas, will this set work on fine-tooth saws too?

P1185123.JPG.6fbe6cb4cbbab0599a8e725dd90

P1185124.JPG.1d2af09715cf21ba2b21b2d6f93

Posted (edited)

    My set has numbers to set the teeth, according to the TPI you match the saw set number as close as you can to the TPI, and then after you set them I lightly use a hammer,[metal] lay the saw on my wooden vise and lightly tap the teeth back just a tad, to narrow the kerf, while still getting the correct set for the teeth.   Search Paul Sellers.com  he has a video or two about setting teeth, it's very helpful

Edited by RichardA
Just remembered a link!
  • Like 1
Posted

Thanks Richard - I was wondering what the numbers on the set were calibrated in ... makes sense that it would be the tpi - goes up to 12 on this set, so probably a bit coarse for the 14tpi saw. I'll certainly check out Paul Sellers' vid.

Posted
9 hours ago, h3nry said:

Thanks Richard - I was wondering what the numbers on the set were calibrated in ... makes sense that it would be the tpi - goes up to 12 on this set, so probably a bit coarse for the 14tpi saw. I'll certainly check out Paul Sellers' vid.

I think if you go lightly, the 12 will work on the 14TPI, just try using a guide, Paul Sellers has a vid with a way to guide the file as you sharpen!  Fleam is something that takes time to learn .again that's where you'll need the guide, to keep it consistant!

Posted

Don't pay much attention to the numbers on a set.  Start with just a little bit and learn what it does.  The easiest way to judge fleam is to draw a bunch of lines on something like a piece of plywood about eight inches wide of the angle of fleam you want with a magic marker. Place it behind the saw, and even elevate it on something if you need to, so you see it behind the file you are holding.  You can easily see if you are holding the angle of the file different from the lines.

 I have probably ten pounds of different saw sets, but stopped tying once I bought a 42X.  It grabs the saw to hold it in position before the plunger starts pushing on the tooth.  I have two of them, with one having the "pusher" ground down to make it small enough for tiny teeth.  42X's go for real money these days, but sometimes you might get lucky.  You can almost always find them on Ebay.  Even though I got mine a long time ago, if I had to pay today's prices, I'd still be ahead if I hadn't put all the money in the ones I didn't like for various reasons.

Posted
1 hour ago, Tom King said:

Don't pay much attention to the numbers on a set.  Start with just a little bit and learn what it does.  The easiest way to judge fleam is to draw a bunch of lines on something like a piece of plywood about eight inches wide of the angle of fleam you want with a magic marker. Place it behind the saw, and even elevate it on something if you need to, so you see it behind the file you are holding.  You can easily see if you are holding the angle of the file different from the lines.

 I have probably ten pounds of different saw sets, but stopped tying once I bought a 42X.  It grabs the saw to hold it in position before the plunger starts pushing on the tooth.  I have two of them, with one having the "pusher" ground down to make it small enough for tiny teeth.  42X's go for real money these days, but sometimes you might get lucky.  You can almost always find them on Ebay.  Even though I got mine a long time ago, if I had to pay today's prices, I'd still be ahead if I hadn't put all the money in the ones I didn't like for various reasons.

Are you referring to http://www.ebay.com/bhp/stanley-saw-set ?

Posted

There is a 42W, 42, and a 42X.  Big difference.  I bought a 42W new in the '70s. The 42X is the only one that has a plunger that comes into contact with the saw holding the position fixed before the "pusher" ever touches the tooth.  It eliminates the majority of the possibility for human error.

There are a couple on that page with very decent prices.  Heck, I would have come out ahead if I had paid the price of the highest priced one at 115.

Posted

Just start with the minimum set and see if the saw is binding.  It is easy enough to add more set later. 

The saw set you have is an Eclipse style that will work as well as a Stanley 42X.  If the plunger is too wide for the teeth of the saw you want to set, you could file it down, but especially for the saw pictured I'm sure you're fine. 

For saw plates I recommend tallow as a lubricant. 

Posted

You guys are awesome - I think that's all the info I was looking for. The saws are cutting nicely now they've been filed. I think I'll just set the rip-saw and leave the carcass saw alone this time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 56 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined