Still learning Posted February 25, 2016 Report Posted February 25, 2016 I have been thinking about upgrading my bandsaw, basic 14" is priced right. Would I be able to resaw hardwoods at 6" with good results or would it be lacking? Quote
Brendon_t Posted February 25, 2016 Report Posted February 25, 2016 I do resaw on my 14" grizzly, with that said it has to be taken very slow. Just last night, I resawed a 10" wide 40" long board of ash for a laminated addition to my chop. It cut in two, slowly and with a finish that must be addressed. If general BS use with the occasional resaw is your need, they do work. If you need a mostly dedicated resaw saw, I'd consider a bigger saw. Quote
wdwerker Posted February 25, 2016 Report Posted February 25, 2016 I resaw occasionally with my 14" Delta/Rockwell. I have a height kit on it and can cut about 12" thick . I replaced the original 1/2 hp motor with a 1 hp. It is still slow going to resaw unless the wood is pretty soft. 1 Quote
jplemons Posted February 25, 2016 Report Posted February 25, 2016 I'm not sure what basic is, so I'm guessing something like the Laguna 1412 isn't it. With that said, I've taken raw walnut logs to mine, thickest about 6", and it sliced through with no problems, except the large amount of sawdust all over the place. Quote
Still learning Posted February 25, 2016 Author Report Posted February 25, 2016 it is a General International. I would like to be able to saw a 6" board thinner, ie: 1 inch into a 1/2 and 1/4 thickness. I do a lot of bigger purpleheart and would love 1/ 4" panels. Quote
wdwerker Posted February 25, 2016 Report Posted February 25, 2016 which General International model ? I see several that the specs seem to be quite capable of 6" thick resawing. You will need to get a resaw type blade and tune up your saw. Adjusting the guides will help control the blade from drifting. Quote
Tom Cancelleri Posted February 26, 2016 Report Posted February 26, 2016 While the bigger and more powerful the saw the fast you can resaw, however I've done 12" resawing on my Laguna 1412, it's all about setup and blade when it comes to resawing. Quote
shaneymack Posted February 26, 2016 Report Posted February 26, 2016 I had a 14" GI saw years ago and it resawed alright. I wasnt as knowledgeable about bandsaws/bandsaw setup 10 years ago as i am now so with the same saw now setup properly, it would do just fine. I have a laguna 1412 now but never resawed with it as i have another saw dedicated to resawing. Im sure the 1412 would do a decent job though. Sent from my SM-N910W8 using Tapatalk Quote
Still learning Posted February 29, 2016 Author Report Posted February 29, 2016 Thanks Shaneymack Quote
Still learning Posted March 7, 2016 Author Report Posted March 7, 2016 Well I have decided to go ahead with this and have watched several set up videos. I watched one video with Alex Snodgrass where he made the comment "no bandsaw should ever have drift", even argued with a guy about it, others say it is not possible. Once I get this set up which opinion should I expect is correct? I would like to believe I could set it up without but don't want my expectations to be set towards unattainable goals. Quote
Brendon_t Posted March 7, 2016 Report Posted March 7, 2016 I have found this to be slightly true in that after a full set up on a brand new blade, I haven't experienced drift but if you change blades, saw through a few knots you might find the blade does drift a bit. Personally, I set up the best I can but monitor the blade throughout a cut. If it drifts, I correct the path. Quote
wdwerker Posted March 7, 2016 Report Posted March 7, 2016 It's better to test cut and adjust the fence to compensate for drift than to think it is going to be perfectly straight every time. I like to have a pencil line on the top edge so I can see if the cut wanders off line. Quote
Still learning Posted March 8, 2016 Author Report Posted March 8, 2016 Ok, thanks, I have lots of practice material to play with until I get it figured out. Shoot for perfection but don't be disappointed if not achieved. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.