bushwacked Posted April 28, 2017 Report Posted April 28, 2017 Curious what your thoughts on this were ... I was thinking the harbor freight would be good enough since tons of people have liked this unit.The other options I was thinking of were the grizzly and the delta. I cant see there being a huge difference in the 3 and really dont feel like paying $5-600 for one with minimal gain. Quote
gee-dub Posted April 28, 2017 Report Posted April 28, 2017 Dad got lucky on his 3rd HF 12" sander and it still runs smooth as can be. I used some QR woodworking vises from HF for years. I had to open 8 of then at the store to get 2 that were usable. This is not a bad thing necessarily. You know what your getting into and there will be a bit of fooling around BUT, you can save a bunch-o-cash if you're diligent. All that being said, I think a combo unit like a Grizzly G0529 or a G1276 or their more expensive cousins make more sense for the footprint. I'm just sayin' Quote
bushwacked Posted April 28, 2017 Author Report Posted April 28, 2017 I was thinking of the G0529 actually ... but I already have the rigid oscillating sander, so that would be useless and I would need to get rid of. However, I do like the sander being portable so I can move around or even put up when not needed. Space would not be a huge issue as I would have the space for that footprint. Just waying portability over a 2 in 1. I am curious if eithers dust collection is better than the other or if they are both mediocre. Quote
wtnhighlander Posted April 28, 2017 Report Posted April 28, 2017 Just an opinion, and may not fit your space requirements, but if I had to do it again, I would certainly seperate my belt and disc sanders. Quote
gee-dub Posted April 29, 2017 Report Posted April 29, 2017 OK, so you're good on a spindle and a small oscillating belt. Back to the HF disc. As mentioned you may have to go through a few and I am definitely NOT saying that the HF is equal to something like the Jet 12B but, you are saving 70%. The number of HF sanders you are willing to go through will be based on what you want to do with it. If you plan to size miters or other parts, table flatness and alignment, wheel travel and all that HAVE to be good. If you're just going to grind down things to approximate sizem the first one you get may be fine. The things you don't want to do is figure that it is "good enough" because all it will do is disappoint you EVERY time. That is worth more money or more time spent trying the next unit. Getting a great deal on a malfunctioning tool is no deal at all. Just be diligent or change the budget and you'll be fine. Quote
bushwacked Posted April 29, 2017 Author Report Posted April 29, 2017 Just an opinion, and may not fit your space requirements, but if I had to do it again, I would certainly seperate my belt and disc sanders. Why is that? Also what do you have that makes you say that? OK, so you're good on a spindle and a small oscillating belt. Back to the HF disc. As mentioned you may have to go through a few and I am definitely NOT saying that the HF is equal to something like the Jet 12B but, you are saving 70%. The number of HF sanders you are willing to go through will be based on what you want to do with it. If you plan to size miters or other parts, table flatness and alignment, wheel travel and all that HAVE to be good. If you're just going to grind down things to approximate sizem the first one you get may be fine. The things you don't want to do is figure that it is "good enough" because all it will do is disappoint you EVERY time. That is worth more money or more time spent trying the next unit. Getting a great deal on a malfunctioning tool is no deal at all. Just be diligent or change the budget and you'll be fine. Agreed. I don't mind going through a couple since it is about 2 mins from my work so I can swap out 5 times a week if needed haha. However. If I go with that delta would that be a much better upgrade than the HF and I could almost guarantee one and done? Quote
..Kev Posted April 29, 2017 Report Posted April 29, 2017 Well, I have an old Grizz belt/disc unit that gave up the ghost (finally) on the belt side. The disc side still works fine and you're welcome to it fee if you'd like it? Shipping would probably be expensive but, just thought I'd toss it out there. Quote
wtnhighlander Posted April 29, 2017 Report Posted April 29, 2017 BW, I just have an old Craftsman 4" belt, 6" disc combo. I have used it a lot, but the arrangement is just awkward. Plus there is only one table that must be swapped between positions. Now that I have the Rigid oscillating belt/spindle sander, I am seriously considering replacing the belt/disc combo with a narrow strip sander and a larger disc. Quote
bushwacked Posted April 29, 2017 Author Report Posted April 29, 2017 Well, I have an old Grizz belt/disc unit that gave up the ghost (finally) on the belt side. The disc side still works fine and you're welcome to it fee if you'd like it? Shipping would probably be expensive but, just thought I'd toss it out there. No worries Kev! I'm not even sure what I want to do yet. I'll normally research a few more months and change my mind and talk myself out of ideas a few 100 times before I pull the trigger haha. BW, I just have an old Craftsman 4" belt, 6" disc combo. I have used it a lot, but the arrangement is just awkward. Plus there is only one table that must be swapped between positions. Now that I have the Rigid oscillating belt/spindle sander, I am seriously considering replacing the belt/disc combo with a narrow strip sander and a larger disc. Oooh gotcha. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.