Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

So I spent part of Saturday tuning up the bandsaw

Featured Replies

Put new tires on it, got it all aligned. Spent some time in that process at the local Woodcraft looking at the Rikon class-equivalent unit to see how it aligned, to get a better picture in my head.

Had one little item to cut at 30°  that would work better on the bandsaw than the table saw, but I ran into a small kink. This thing could really use a larger table. I had to move the rail down & clamp the fence in place. Certainly not elegant but it got the job done.

The real weak point of the saw is not the saw but the table. The miter fence is a joke. The rip fence is adequate for its size. Their drawback is that they're just a bit too small. What I need is either a rear rail or a larger bed. I think, if I could epoxy in some bosses, adding a rear rail might be enough. (The fence has another part, removed for this task, that would let me extend its length to meet a rear rail.)

What has anyone here done along this line, either bed or extended rails?

 

tilt2.jpg

This is the kind of cut most would do on a table saw or a jig saw with a straight edge. I don't think there is a good solution for the band saw when trying to do angle cuts on large pieces. Especially the way you have it setup so you are putting the piece between the blade and the fence. You run the risk of binding if you get much drift.

I always feel good after giving a tool or two a clean up, preventative maintenance job or what not.  Remember that anything you hang off your table applies stress directly to your trunnions.  That is a 10" saw, yes?  I think the table size may be designed for the machine's ability to support it.  I have a 10" saw and it does great for small curvy stuff.  I actually probably get away with using it beyond its capacity a bit but, I do keep that capacity in mind. 

  • Author
1 hour ago, minorhero said:

This is the kind of cut most would do on a table saw or a jig saw with a straight edge. I don't think there is a good solution for the band saw when trying to do angle cuts on large pieces. Especially the way you have it setup so you are putting the piece between the blade and the fence. You run the risk of binding if you get much drift.

 

22 minutes ago, gee-dub said:

I always feel good after giving a tool or two a clean up, preventative maintenance job or what not.  Remember that anything you hang off your table applies stress directly to your trunnions.  That is a 10" saw, yes?  I think the table size may be designed for the machine's ability to support it.  I have a 10" saw and it does great for small curvy stuff.  I actually probably get away with using it beyond its capacity a bit but, I do keep that capacity in mind. 

The piece was small so there wasn't any concern with it binding up. My tune-up dealt with the drift issue. It was also 3/4" MDF so the cut was easy and quick. And the edges came out smooth.

Concerns appreciated and noted.

**

I've not gotten into any resaw work yet. Even though it will do 6" I don't think I"ll go past 4. The relatively short 72" blade wouldn't get enough time to cool on its way around. And while I find this saw very suitable for small-volume work, I am keeping my eyes out for used older Delta or similar. (IOW, while this class of saw is not a bad choice I can see outgrowing it in the next couple of years. At least it's not a basic craft saw like the Delta BS100 & similar units, as I started with.)

  • Author

Also, the knobs on this series weren't extremely durable. Turn it too snug and those long arms break off the bolt inside. Soft plastic.

I've substituted a knob from a Dewalt miter saw. A much better part.1c75dec305e0b634b67519af1be0587f.jpg

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

Just a quick side note, Marc just put out a video on tuning the bandsaw.  Haven't watched it yet, but I'm expecting it to be pretty good if he's redoing an older vid. 

For me, the best video on tuning up the bandsaw (especially for resawing) was done by Alex Snodgrass from Carter Products. There is even a DVD you can buy from Carter or a booklet which details the whole process. Alex has done demos on tune-up at woodworking shows for years and I always stop by and watch. It's always a good review for me. When followed, the steps in the booklet yield great results and improved the my resawing on my Rikon significantly. It's a good resource.

Here's the YouTube link for one of his demos from a woodworking show - 

There is also a video from Mark Spagnolo's shop by Alex when he stopped by there. I would guess they are about the same, but some of the steps might be slightly different in the last one.

For me, the best video on tuning up the bandsaw (especially for resawing) was done by Alex Snodgrass from Carter Products. There is even a DVD you can buy from Carter or a booklet which details the whole process. Alex has done demos on tune-up at woodworking shows for years and I always stop by and watch. It's always a good review for me. When followed, the steps in the booklet yield great results and improved the my resawing on my Rikon significantly. It's a good resource.

Here's the YouTube link for one of his demos from a woodworking show - 

There is also a video from Mark Spagnolo's shop by Alex when he stopped by there. I would guess they are about the same, but some of the steps might be slightly different in the last one.

 

Alex clarifies and goes into better detail on the important steps In the new video with Marc. It's a worthwhile watch, even if it lacks the reindeer ornament demonstration.

 

 

Sent from my iPhone using Tapatalk

You can build an auxiliary table if you really want to.  When I find myself in a situation where my bandsaw table size is an issue, I usually just take a tool to the wood instead.

 

Td3ZC6J.png

 

 

I know you're not supposed to speak truth around here because it could hurt someone's feelings, but to be perfectly honest that 10" saw is going to be the limiting factor most of the time, not your table size.  It just doesn't have enough power or capacity to do a lot of the work required in furniture making.  You should really set it aside for curves in thin stock and buy a 14" or larger for ripping and resawing anything an inch or thicker.

I have that same saw with Craftsman badge and colors.  It's actually a decent little saw, but I only use it for small things.  I bought it to use up on scaffolding.  Since then, it probably gets used more than the other bandsaws, but it's not one for resawing much of anything.  I keep a 1/4" 6 tooth band on it.  I don't think it would hold up long if you try to push it hard.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.