Nick2cd Posted January 21, 2011 Report Posted January 21, 2011 I have just started making my first few cuts on my SawStop contractor saw. it came with a zero clearance insert. the blade sounds like it's making contact with the insert when i spin it by hand. i have tried turning on the saw and raising the blade up through the insert to full height and then back down again, but im still getting a little bit of contact. ?????? i know it's contacting the insert only becuase when i remove the insert, i don't hear the contact any more. is it normal to still have a bit of contact with the insert even after i have cut it with the blade spinning? Quote
Beechwood Chip Posted January 21, 2011 Report Posted January 21, 2011 I installed my ZCI on my Sawstop contractors saw a few weeks ago. I don't really remember any problems, but there may have been some faint "tinging" sounds for the first few cuts. Quote
tkremer Posted January 21, 2011 Report Posted January 21, 2011 I have the 3HP Professional Cabinet Saw and when I use a ZCI I hear it too. What's happening is that the sides of the teeth are very lightly brushing against the insert. As you mentioned, it's really nothing to worry about because it won't dull the blade, it won't set off the brake, etc. It's actually a bit of a good thing because it means your ZCI is really ZERO CLEARANCE. I should clarify that I don't FEEL anything when I spin the blade by hand, but it does sound different when it spins. Quote
jon003 Posted January 21, 2011 Report Posted January 21, 2011 My ZCI was very tight out of the box with a Forrest WW2. So far, I haven't had any chattering or contact though. 1 Quote
ChetlovesMer Posted January 21, 2011 Report Posted January 21, 2011 I had to actually run out and check mine. I couldn't remember if my ZCI made any noise. Mine doesn't seem to make any noise at all. I can't say whether it did or not when it was brand new, but now 3 years later, it is as quiet as a church mouse. Quote
Jerry_in_SD Posted January 25, 2011 Report Posted January 25, 2011 That is interesting. When I first got my PCS, I used the stock SawStop blade that came with the saw. I did hear that sound as well. I eventually switched back to my Forrest WW II after it was received from sharpening. That noise did not appear with the WW II. My cuts were better also with the WW II. I will stick with the WW II from now on. Maybe it is the blade? Quote
Nick2cd Posted January 25, 2011 Author Report Posted January 25, 2011 That is interesting. When I first got my PCS, I used the stock SawStop blade that came with the saw. I did hear that sound as well. I eventually switched back to my Forrest WW II after it was received from sharpening. That noise did not appear with the WW II. My cuts were better also with the WW II. I will stick with the WW II from now on. Maybe it is the blade? i think this is a very viable theory. maybe the sawstop blade has a bit less rigidity than the forrest and has a bit of oscillation at operating speed? i must say, the more i use the saw, the less evident the sound becomes. Quote
ChetlovesMer Posted January 25, 2011 Report Posted January 25, 2011 That is interesting. When I first got my PCS, I used the stock SawStop blade that came with the saw. I did hear that sound as well. I eventually switched back to my Forrest WW II after it was received from sharpening. That noise did not appear with the WW II. My cuts were better also with the WW II. I will stick with the WW II from now on. Maybe it is the blade? This may explain why my 3 year old saw is as quiet as it is. I've been using a Forrest blade for a while now as well. Quote
Beechwood Chip Posted January 25, 2011 Report Posted January 25, 2011 I was using a Freud thin kerf. Quote
jcolliflower Posted September 13, 2012 Report Posted September 13, 2012 Hello, fellow woodworkers! I'm a SawStop fanatic so I must comment on this post. The SS stock zero-clearance inserts are better than most stock plates, but still...it's a stock plate! I bought an aftermarket ZCI for my SawStop and it is amazing! I went through 2 sets of single and dado plates in two years and I thought I'd have to keep buying them, as I use my saw a lot. But I was told about an aftermarket plate from a guy on Lumberjocks and I checked it out. Awesome! It is made of aluminum and the "inserts" are replaceable (wood) and easy to make. It's like the old WoodDynamics plates, if anyone remembers those. (They were the best.) I bought mine from Infinity Tools, but I also saw they were being sold on Amazon.com. It's truly the answer to SS's throat plate problems! Happy woodworking! Quote
CessnaPilotBarry Posted September 13, 2012 Report Posted September 13, 2012 The noise is totally normal. I made a bunch of 1/2" Baltic birch plywood ZCI's for blades, dados, even some dual-blade tenon versions. Most are reversable, end-to-end, for dual dado widths, as I don't use a riving knive with dados. The inserts are leveled with 1/4-20 set screws. I cut ~ 25 blanks at once using a pattern bit, the original insert, and carpet tape. I cut rectangular blanks first, and routed one to shape. The first copy then became the routing and drilling pattern for the other 24. The 25 inserts cost ~ $2 each and a total of about 2 hours of my time. The blanks sit in a drawer, when I cut the slots as I need new configurations. Since most are dado inserts, clearance to start the cut is not a problem. The cutouts on the back of the stock inserts only come into play at extreme blade tilt and/or extension. If my inserts lack of them becomes a problem, I simply pop in the stock insert for that cut. Quote
walnut_weasel Posted September 13, 2012 Report Posted September 13, 2012 I have the same sounds when spinning the stock blade by hand and also when I first turn it on. My frued blade does not make a sound. I assume it is because if the increased quality of the blade - more flat and better aligned teeth? Quote
jmaichel Posted September 17, 2012 Report Posted September 17, 2012 I have just started making my first few cuts on my SawStop contractor saw. it came with a zero clearance insert. the blade sounds like it's making contact with the insert when i spin it by hand. i have tried turning on the saw and raising the blade up through the insert to full height and then back down again, but im still getting a little bit of contact. ?????? i know it's contacting the insert only becuase when i remove the insert, i don't hear the contact any more. is it normal to still have a bit of contact with the insert even after i have cut it with the blade spinning? I installed my ZCI on my Sawstop contractors saw a few weeks ago. I don't really remember any problems, but there may have been some faint "tinging" sounds for the first few cuts. How do you both like the contractor saw? Is their a reason that you didnt get the PCS ? Was your intention to keep the saw for the long haul when you purchased? Just curious? Quote
Beechwood Chip Posted September 17, 2012 Report Posted September 17, 2012 I like the contractor saw. I had set an arbitrary budget and the PCS was too expensive. I expect this to be the last table saw I buy. Quote
jmaichel Posted September 17, 2012 Report Posted September 17, 2012 I like the contractor saw. I had set an arbitrary budget and the PCS was too expensive. I expect this to be the last table saw I buy. Thanks! Quote
Nick2cd Posted September 24, 2012 Author Report Posted September 24, 2012 How do you both like the contractor saw? Is their a reason that you didnt get the PCS ? Was your intention to keep the saw for the long haul when you purchased? Just curious? i love my SS contractor saw. my saw was purchased for me as a gift by my wife. besides dust collection, i just don't know how much better a cabinet saw could perform. the contractor is built like a tank and maintains surgical precision. i upgraded to the better fence and the cast iron wings. couldn't love this saw more! Quote
Beechwood Chip Posted September 24, 2012 Report Posted September 24, 2012 ditto on the cast iron wings and fence upgrade. I'd prefer better dust collection - I bought mine a month or two before the dust collection blade guard became available. Quote
vbdcb Posted September 30, 2012 Report Posted September 30, 2012 My 20 y/o inexpensive Delta gave out on me ripping some 8/4 stock last week and I have decided to get a Sawstop Professional 3hp this week. I was leaning toward a Grizzly, but thought that with a purchase like this that I plan to keep for the next 20+ years the additional cost is about $75 a year in injury insurance. My wife couldn't agree more. I am looking forward to getting it set up and starting cutting again next weekend. My old ts: Quote
TLC123 Posted January 30, 2014 Report Posted January 30, 2014 My ZCI was very tight out of the box with a Forrest WW2. So far, I haven't had any chattering or contact though. Nice shop there. I LOVE an organized and clean shop. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.