Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Darkening danish oil door

Featured Replies

I stained a new Pine Barn Door with Watco "Dark Walnut" and I just don't think it is dark enough, even after 2 coats. . If I keep adding more coats (knowing it is not like a regular stain) what are the chances it will darken up? If I sand it lightly will it take more stain? Stripping all the color out is not an option. 

Thanks...and time is of the essence. Unfortunately. 

The short answer is the same for most finishing questions; test board.  Since you've already applied a penetrating oil finish it will depend on the pine somewhat.  A lot of pine and ash have such a natural yellow content that colorants will be affected.  The blue / red ratio will vary on the type of brown but, either will lean toward green with yellow added.  I had some ash that I had to stain heavily as opposed to using my usual penetrating oil-type finish to tone down the green. 

You can probably add a darker color to the piece in the form of your Watco with a few drops of brown dye.  Next time, test board first, project finishing second.

They also sell Watco in different colors, maybe a brownish one like oak or walnut might work. Please make some test boards before you try anything on your door.

  • Author

Thanks everyone. I did do a test board. But....after we removed it from its staining location the whole project just seems to light. Sometimes a practice piece can't give you the whole picture. I went with Black Walnut thinking it would be darkest...but pine stains light sometimes. Just wondering from you wood guys your experience with the Danish oils. I have always used regular stains, not oils, before followed by poly. Oh well....could have stuck with what I know so well...but I just did not want to poly this piece. I will try go over it a few more times. Thanks for the input. 

It will continue to get darker with each subsequent coat...but the problem with DO is if you don't wipe off the excess after applying a coat, it takes forever to dry, and will give you an inconsistent sheen.  So you're kind of in a jam since wiping back the excess means minimal darkening with each coat.  The walnut DO is probably best suited for actually finishing walnut, where it doesn't really change the color of the wood but just darkens what already exists.

Since you already have a test board going, you might buy a little can of gel stain and see what happens when you put a coat on top of the DO.  It should be okay as long as the DO is dry.  If you were starting from scratch my recommendation for staining pine would have been a coat or two of shellac, then gel stain, then a varnish top-coat.  Pine tends to blotch badly without a base sealer.

**I have not tried this ~ but I have no reason to think this wouldn't work.**

 

Go buy a can of minwax "darker" color oil stain and mix to the Watco. Remember your portion to how much to what for mixing more. USE A SCRAP TO TEST THE COLOR AND IF THE PRODUCTS PLAY NICE WITH EACH OTHER.

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.